Hangman - Speaker Hanging Kit (2-Pack) - Silver

Display your stereo equipment proudly with this heavy-duty Hangman speaker hanging kit. Two packs of interlocking mounting brackets made of aircraft-grade aluminum ensure durable placements. The built-in level ensures accurate installation, and this Hangman speaker hanging kit can hold up to 50 lbs. per bracket for versatile use in your audio space.
Save $2
Was $9.99
Cardmember Offers
Frequently bought together

Item you're currently viewing

Hangman - Speaker Hanging Kit (2-Pack) - Silver - Larger Front
Hangman - Speaker Hanging Kit (2-Pack) - Silver
  • Item you're currently viewing
  • $7.99
Offer disclaimer


What's Included

  • Hangman Speaker Hanging Kit (2-Pack)

Ratings & Reviews

Overall Customer Rating:
100% of customers would recommend this product to a friend (3 out of 3)


Compatible with most speakers

So you can optimize room placement to ensure a lush sound scape up to 60 lbs.

Wall bracket design

One bracket attachers to the back of the speaker and engages the other bracket that installs on the wall.

Integrated bubble level

Adjust to find the proper angle and fasten the mount.

Aircraft-grade aluminum brackets

Provides reliable fixing speakers.


Enables use with a pair of speakers.

Overall customer rating

Rating: 4.3 out of 5 stars with 3 reviews

100%of customers would recommend this to a friend



Looks like there aren't enough negative mentions yet.

Most helpful reviews

See all customer reviews
  • Rating: 4 out of 5 stars

    The suckers work, but....

    • Verified Purchaser
    • My Best Buy® Member

    At "first look", the brackets look kinda "cheesy", seeing as the wall bracket is made from 0.04" (1 mm) extruded aluminum and the speaker bracket is made from 0.05" (1.26 mm) extruded aluminum. However, my "fears of cheesiness" were allayed when I attached them to the speaker and wall - THEY ARE QUITE STRONG! The included "bubble level" for the wall brackets is a GODSEND! as long as you follow the directions on the wall bracket, you WILL NOT have an "off-level" wall bracket! Be careful though: the level WILL "FALL OUT" OF THE BRACKET if you're not careful to remove it AFTER you mark the 2nd drill hole in the wall and "pivot" the bracket for drilling. The bracket uses TWO of the LONG screws for mounting (either in a stud or using the included drywall anchors). The speaker bracket mounts Just As Easy. Find the "center point" on the top of the rear speaker, align the bracket so it's flush with the top "inner edge", and screw the bracket to the back of the speaker using two SHORT screws. Apply two of the included clear "bumpers" to the lower back corners and you're ready to mount the speaker to the wall. Here is where I didn't give a 5-star rating: Using a pair of long-nose pliers, I had to slightly "bend out" the speaker bracket so it would engage the wall bracket edge. However, once the speaker bracket "engages" the wall bracket, a couple of "raps" on the speaker caused the brackets to fully "mesh", and "mesh" QUITE TIGHTLY! You can slightly adjust the speaker from side-to-side (i.e., "center" it) by "rapping" on the speaker sides. Your fist will do - no need for a hammer! Once the speaker is mounted, IT WILL NOT MOVE! the "bumpers" on the bottom corners will help prevent unwanted "vibration" as well as keep the speaker from "moving" later on. If you need to "unmount" the speaker, give it a few sharp "raps" from the bottom to disengage the mounts. Final words: 1) PAY HEED TO THE LOAD RATING! these brackets are made for "bookshelf" type speakers that weigh LESS THAN FIFTY (50) POUNDS! anything heavier could risk "ripping" the wall mount from the wall. 2) DO NOT install the SPEAKER bracket lower than one-third the speaker's height (i.e., if the speaker is 12" tall, mount it NO LOWER than 4" from the top edge). This will prevent "lever effects" from potentially "ripping" the wall bracket from the wall (especially if mounted with the DRYWALL ANCHORS). 3) For the drywall anchors: DO NOT drill a hole LARGER than 3/16" or the anchor will not properly "seat". If you don't have a 3/16" drill bit, the shaft of a #1 PHILLIPS will punch a perfect-sized hole. Install the anchor then lightly "tap it flush" into the wall. 4) If you do need a drywall anchor, try to align the bracket so one of the screws goes in a wall stud. This will guarantee the drywall won't take "the full load" of the speaker.

    I would recommend this to a friend

  • Rating: 5 out of 5 stars

    Great product

    • Verified Purchaser
    • My Best Buy® Member

    Easy great install . It brings out the location sound of my rear center channel speaker that is hung on my wall , behind my rear soundstage .

    I would recommend this to a friend

  • Rating: 4 out of 5 stars

    love it

    • Verified Purchaser
    • My Best Buy® Elite Plus Member

    this works really well and simple and inexpensive.

    I would recommend this to a friend

Product images, including color, may differ from actual product appearance.