How do you put it on? null

the tablet fits into the frame, it's snug, but it makes the tablet secure, not too difficult, my wife did it in about 5 minutes using a small plastic device that's provided to open the frame while inserting the tablet ...it's similar to putting a picture into a frame, you install the screen saver before inserting the tablet into the frame...the screen saver is a clear laminate, very thin ,but strong that protects the tablet screen....I really enjoyed watching her do this project....did it very well and very fast.

It's hard to put on - fits VERY tight but if you work gently with it, it will finally go on. With it so tight, you don't have to worry about it falling off! Hope this helped.

I have to say that it took me a while to figure out how to put this case on properly once I removed it from the package. It was not easy as the directions were not very clear on installation. The outer portion of the case is a hard rubber ring. If you hold the case right side up facing you with the selfie camera on top and the charging port on the bottom, look at the 3 o'clock position. There is an arrow that points to the right. Start at that position and work the hard rubber ring off pushing it to the right. Proceed clockwise towards the bottom portion of the case and continue all the way around until the rubber outer ring is off. It takes a while to do. The ring is very tight especially when you get to a corner. Put your tablet into the bottom portion of the case. Line it up so the camera is on top and the charging portion is on the bottom. When that is done start at one corner and reinstall the outer rubber ring slowly. Make sure it is seated properly against the lower portion of the case as you go along. It will look perfect and install properly without damage to the outer ring if you take your time. Good Luck. Also, if you extend the kickstand in the back to stand up the tablet by itself, when you are finished push in the button at the top of the kickstand to close it properly. It took me a while to figure that out also. Do not force the stand closed.

“How do you put it on?”

Asked by Howdoyouputiton 5 years ago

Answer This Question

See all questions & answers

SaharaCase - Protection Case for Samsung Galaxy Tab S5e - Black-Front_Standard

1-3 of 3 Answers

the tablet fits into the frame, it's snug, but it makes the tablet secure, not too difficult, my wife did it in about 5 minutes using a small plastic device that's provided to open the frame while inserting the tablet ...it's similar to putting a picture into a frame, you install the screen saver before inserting the tablet into the frame...the screen saver is a clear laminate, very thin ,but strong that protects the tablet screen....I really enjoyed watching her do this project....did it very well and very fast.
Answered by samsung 5 years ago
Sorry, there was a problem. Please try again later.
It's hard to put on - fits VERY tight but if you work gently with it, it will finally go on. With it so tight, you don't have to worry about it falling off! Hope this helped.
Answered by Annie 5 years ago
Sorry, there was a problem. Please try again later.
I have to say that it took me a while to figure out how to put this case on properly once I removed it from the package. It was not easy as the directions were not very clear on installation. The outer portion of the case is a hard rubber ring. If you hold the case right side up facing you with the selfie camera on top and the charging port on the bottom, look at the 3 o'clock position. There is an arrow that points to the right. Start at that position and work the hard rubber ring off pushing it to the right. Proceed clockwise towards the bottom portion of the case and continue all the way around until the rubber outer ring is off. It takes a while to do. The ring is very tight especially when you get to a corner. Put your tablet into the bottom portion of the case. Line it up so the camera is on top and the charging portion is on the bottom. When that is done start at one corner and reinstall the outer rubber ring slowly. Make sure it is seated properly against the lower portion of the case as you go along. It will look perfect and install properly without damage to the outer ring if you take your time. Good Luck. Also, if you extend the kickstand in the back to stand up the tablet by itself, when you are finished push in the button at the top of the kickstand to close it properly. It took me a while to figure that out also. Do not force the stand closed.
Answered by Tonowanda427L88 5 years ago
Sorry, there was a problem. Please try again later.