Customer Ratings & Reviews

The fact that you can fit 7 fans in it and comes with 3 already installed makes for a great selection. The case has what seems to be more room than one would think. Was easy to build in and cable management was fairly easy.

I ordered this case for my first build. Pros: 3 include fans that have rgb built in Including lighting node to sync up rgb with other corsair products Good airflow overall Great unboxing experience Mid Tower design is really good if you want a ATX case with a slight compact feel Cons: You can't mount a radiator on the top unless you are using a low profile ram module You also cant mount a radiator on the front with a fan below it (unless the fan is a bit smaller, where in my case it was with the case fans) Cable management was kind of a pain considering the space between the back side panel and back of case There was a small dent on the back panel so it doesn't sit in fully flush(Maybe improve the packaging a bit more.

I really like the look and feel of this case. The front cut outs make the included RGB fans look great even though they only have the internal LEDs (fan hub, not the outer ring). The ONLY drawback I've found is that the slightly lower profile make using a liquid CPU cooler difficult because it leaves little room for the radiator fans and the RAM on most mother boards. The cabling is a little tight, but that wasn't really a problem for me. Over all, it is a good little case that's easy to work on, but if you're going to be using larger components, go with one a bit bigger.

Comes with 3 high end corair fans preinstalled with the rgb node pro for easy lighting,great build quick for 100, it's a compact mid tower so expect it to be tighter.

Awesome case made of quality materials. First of all, its a small case, so expect it to be a bit cramped trying to do cord management. The front vent not only looks cool but does a great job providing an extra source of air most cases do not have. Right now I only have the 3 case fans that come stock but it is doing better than the 6-fan inwin 303 case I swapped out for this. It looks nice and is very light and easy to transport now which is great. The i/o ports on it are nice and accessible and look good on the top. Magnetic dust filter is very convenient.

Used to crazy fan of this brand and will say this case didn't disappoint. Looks great after being set up and additional RGB components look great in it. Compatibility with other products is something you research prior to purchasing and although I didn't think it would work well with a CM RGB Heatsink it actually did. My only wish it that it would have came with an RGB exhaust fan (same series as the 3 provided case fans) but at this price one really cannot complain. Good Quality, easy to build in (once again research falls on the buyer). Nephew loves it!

Decent airflow, decent enough cable management room and three included fans with a touch of rgb? Definitely a good choice. Only problem was putting the psu in.

i was able to get this on during the black friday sale. case looks cool and comes with 3 pre-installed fans. when i opened it however i found it was a lot smaller than my other case (mid/large case from a pre-built) my aio wouldn't fit after my ATX motherboard was in and i had to front mount the aio which forced me to move the fans from the front of the case to the top. i honestly dont know if a 2 fan gpu will fit inside now and i'm waiting to upgrade im new with pcs so i wasn't mad i just suggest making sure you know what will and won't fit inside

This is a really good computer case. It has great airflow and a good design when it comes to aesthetics. The included RGB fans and controller are a great value, but there are some shortcomings... literally: 1. GPU room is on the tight side. I have a NVIDA 2070 Super FE and it looks like it would barely fit a front mounted radiator. 2. There really doesn't feel like there is enough room to cable manage both behind the motherboard or in the PSU shroud with the HDD cages in. I know this is a small case, and I love the idea of smaller builds so that you have more desk space, but I think about an inch longer and 1/2 inch wider could have done wonders.

This case is pretty cute, but it is super small! The product page says it supports the H115i cooler but that’s not possible unless you tuck it down in the front. You will need a smaller graphics card to make that happen and even then you’re giving up the little bit of empty case space down below. This case isn’t going to work for a H115i cooler, larger graphics card, and cable extension kit. I bought it specifically thinking it would work well with the cooler (preferably in a top mount format) and it did not, so I did end up returning it. This case would be great for someone with a 2 fan graphics card and normal fan for CPU cooling.

Has a fine mesh screen to limit dust bunnies from being created in the case. Was a tight fir with my mobo and my icue water cool system.

Looking for a nice case, with enough airflow to keep your unit running cool, all while not breaking the bank? This thing fits your bill! Simple layout with a cool clear side panel to show off all your RGB and clean components! Decent size with plenty of room for whatever you want to stuff inside of it. Slightly smaller footprint than the 4000D, plus it comes with some RGB fans! My only down side to point out is the rubber pass-throughs are kinda chinsy, but they seemingly work just fine!

Probably was not the best choice for my first build as this case does require some special attention to cable routing and securing. Quality is amazing and the RGB fans with the Corsair lighting node was cool to have included even though I wasn't too concerned about lighting. I haven't pushed this rig too much yet but I've had ZERO issue with heat as airflow seems great (5 case fans - 3 intake 2 exhaust). I do have concerns about future upgrades when considering GPUs as the length of the case will limit options. Overall a very good case and for about $100 and included fans it was a great value.

Great case, has a lot of ventilate for sure. Few things to mention is case is small, you HAVE to adjust the Hardrive slot to fit most power supplies or remove harddrive slot all togeather. It comes with 2 SSD bracket, and a light node. (Does NOT come with a fan hub). You will not be able to fit any 3fan watercooler in this, but it does have slots for up to 8 fans, including a fan spot on the bottem of the case, Though most of your wires are going to be jumbled in the little space your givin. The case is pretty solid and is serving me well

I do really like this case, has potential for incredibly high airflow. Very durable steel design, and fits an ATX Motherboard fine. My advice though.. COORDINATE all your components carefully or you'll regret it. It can be a little tight especially around the power supply. Overall with careful planning and measurement, Id absolutely recommend this Mid-Tower.

This case is a steal. It is equipped with 3 120mm fans from the Corsair LL series along with the RGB controller node. You are essentially paying for the fan kit and getting a computer case for free. It is compact but has good airflow for its size. Has a tempered glass panel on its left side and a magnetic dust filter on the front. If you are looking to downsize from a bigger case this is the case for you. Supports ATX sized motherboards so you don't have to settle for mini-ITX or micro-ATX motherboards.

Great case. Beautiful glass side. Three SP120 rgb fans. Comes with an icue controller. Fits ATX and mATX. Allows for 240 mm radiator on top, 360 mm on front. Up to 6 120 mm fans overall. PSU shroud isn't hard to insert the PSU into. Cons: GPU Length must be < 300 mm. You can get approx. 10 mm more if you lose a case fan on the front. So, long 3090s, 3080s, 6800 XTs, and 6900 XTs will likely NOT fit. No USB-C header on front. Otherwise, perfect case for me.

Bought this case because the previous case that I was using was from a prebuilt and I had basically built a custom PC in it one piece at a time. The prebuilt case did not have good airflow and was causing some overheating issues with my 5700XT GPU and Ryzen 7 3700x CPU cranking out some heat. I purchased this case and 3 additional fans to go in it and my overheating issue was resolved. I do have a couple of cautions for anyone looking to buy this case. It is a high airflow case meaning that you will see a quicker or more significant amount of dust build up inside the case. There is a fine mesh screen that covers the intake fans on the front of the case but it can only do so much so be prepared to need to remove the glass and blast some canned air through every few months. The other caution that I will throw out there is that the space between the back of the motherboard mount and the back panel of the case is a little tight. If you are going to be running more than 3 fans and found yourself having to use a Corsair Commander Pro and Lighting Node Core because your motherboard likely does not have 6 USB fan headers and you did not want to use a spliced cable to power them you will need to find an alternative solution for placement of 1 of those 2 pieces of hardware. I personally removed the HDD cage since I do not have a spinning drive anymore but if you need the cage you may be crunched for space. Also if you have a need for the HDD cage you will want to make sure that you use as few cables as possible since there is not much room for cable tucking if left in. Overall I love this product and am very happy with the result.

Love this case. First Corsair case and it comes with the 3 corsair rgb fans in front and 1 regular corsair fan in the back. Just plug in my corsair aio with rgb combined with corsair vengeance pro rgb ram and everything syncd up on my asus prime z390 A mobo. Great ventilation. Good airflow. Fits 240 on top and 360 in front. Enough room for a 3 slot card. And very good cable management ports included to hide everything. Also didnt hurt that it was on sale.

Excellent airflow, amazing price for including 3 RGB fans, SSD mounts, magnetic filters and PSU basement. Love it.