A:AnswerAbsolutely! If your receiver has a phono input, use that . Otherwise, this turntable has it's own preamplifier so you can connect to any input .
A:AnswerThe needle (stylus) can be replaced, but not the arm. If you are looking for the capability of replacing the entire cartridge assembly for upgrading, you might consider the higher end turntable units. This is not one of them.
A:AnswerI don’t know about a manual, but to go from Bluetooth to a receiver you simply need to plug in the rca cable to the back of the turntable and connect it to your receiver.
A:AnswerIs this happening only when using the turntable wirelessly (connected via Bluetooth), when using it hard-wired, or both? Is it skipping as in the needle is physically stuck in the same spot on the record (the tonearm does not progress) and the same section of the record is repeated over and over, OR is the sound just dropping out momentarily throughout the record as the record plays (the tonearm DOES progress)? If it is sticking, exchange this unit for another one as this could be caused by a number of factors. If it is dropping out only when using the wireless connection, you are experiencing interference from another electronic device nearby. Keep the turntable away from wireless routers as these seem to be the most common source of interference at this time. As much as 30 feet between a router and Bluetooth turntable may be required.
A:AnswerThis turntable does not feature Bluetooth, but it can be wired to the Polk DSB 1 Sound Bar using the 6 ft 3.5mm male to 3.5mm male analog cable that was provided with the sound bar.
There is a Bluetooth version of this turntable, the AT-LP60XBT-USB, but we cannot guarantee the compatibility of it with the sound bar.
A:AnswerThe AT-LP60X comes fitted with the AT3600L Cartridge. The cartridge itself is an integral part of the tonearm and cannot be changed, only the stylus can. Use the ATN3600L Replacement Stylus when the stylus needs changing.
A:AnswerThis turntable uses a universal power supply (AC Adapter) and works with voltages ranging from 100 to 240V, 50/60 Hz. The provided power supply will work for you in terms of voltage, but you will need a plug adapter in order to accommodate the outlet configuration.
A:AnswerNot directly, no. These Klipsch Heresy (H= Heresy, B=Birch, R=Raw) speakers are passive type speakers. They are intended to be connected to a stereo amplifier or receiver as they have no power on their own. The turntable would connect to a set of inputs on the amplifier or receiver, and the speakers would connect to the speaker outputs on the receiver.
A:AnswerDid you install the drive belt? The belt comes pre-installed around the drive rim on the flipside of the aluminum record platter, but you have to finish installing it by placing it around the brass-colored motor pulley located in the upper left corner of the turntable. Place the belt around the motor pulley after setting the platter on the center spindle. To check this, simply remove the black felt record mat from the turntable and rotate the aluminum record platter by hand until one of the large rectangular shaped openings in the platter is located in the upper left corner of the turntable (at about the 10 o’clock position). Look into the opening and locate the brass-colored motor pulley. Is the belt around this pulley and is the belt taught? The belt does NOT go around the white post located on the right side of the turntable (at about the 2 o’clock position).
A:AnswerExchange this unit for another one through the reseller from whom it was purchased, pending their exchange policy, or ship it to our Service Center for repair/replacement. The factory warranty period for the turntable is 1 year from the date of purchase. Following is a link to our Repair Return Instructions should you need to ship the turntable to our Service Center. Along with the completed ATUS Service Form, also enclose a copy of your dated sales receipt so we can honor any warranted repair/replacement that may apply. The ship to address is the Stow, OH address shown at the bottom of the form. Please note the special instructions for shipping turntables in for service, we do not require all of the components.
Do NOT ship the platter or dust cover and secure the tonearm to the tonearm rest using a wire tie to avoid damage to the stylus or tonearm assemblies during transit.
Service – USA - Repair Return Instructions
https://www.audio-technica.com/en-us/support/repair-service/
A:AnswerBeing a fully automatic type turntable, the tonearm will automatically lift off the record at the end of play, return to the tonearm rest, and the motor will shut off. You may stop the turntable at anytime by pressing the stop button on the front panel.
A:AnswerPerfect length, only tw0 things I I don't like .
1. the power cord , a square plug that converts AC power to DC power. I never leave those plugs plugged into an outlet they get hot ..
2 . No ground wire to hook up to the receiver..other then those two no other problems
A:AnswerCorrect. In addition to having Bluetooth, a single 3.5mm stereo Analog Out jack is provided on the back of the turntable for making a wired connection. A 3.5mm stereo to dual (left and right) RCA male plugs audio cable is provided.
A:AnswerAn alternative to the receiver with passive type speakers connected method, is to connect the turntable directly to a set of powered (aka active) type speakers. This method eliminates the need for a separate receiver or amplifier between the turntable and speakers. Powered type speakers will have the amplifier built into them. At least one of the speakers will need to plug into an AC power outlet and we recommend models that have a volume control on them as there is no volume control on the turntable. Make certain that you place the preamp selector switch in the correct position based on the type of input (phono or line) that is on the speaker.
