A:AnswerHi Ty,
7.2 Ch x 145W per channel (6ohms, 1kHz, 1ch THD 0.9%). If you are trying to connect speakers. We recommend connecting wired speakers with a nominal impedance of 6 ohms to 16 ohms. We also recommend using speaker wires that are anywhere between 12 to 16 gauge. These are most commonly used for connecting speakers to an amplifier or an Audio/Video (A/V) receiver
Regards,
David
A:AnswerHi Wesley,
No, you cannot connect a wireless speaker to this AV receiver. We recommend connecting wired speakers with a nominal impedance of 6 ohms to 16 ohms. We also recommend using speaker wires that are anywhere between 12 to 16 gauge.
Hope this helps!
David
A:AnswerReceiver supports Dolby vision but depends what you are plugging into receiver more so if you get Dolby vision. Sometimes the streaming device needs to be forced to stay on dolby vision like my Roku Ultra. As a personal choice to get the best visual experience I plug streaming device that I will use for my streaming experience directly to the tv. All peripheral devices like blueray player and gaming system I will plug into the reciever.
A:AnswerHi Rich,
Front high speakers, top middle speakers, and Dolby Atmos enabled speakers are referred to collectively as “height speakers”. See page 15 from this link below for more details regarding your concern.
https://www.sony.com/electronics/support/res/manuals/4726/890436b47fd2ffcc4003f34dc5f2592c/47269051M.pdf
Hope this helps!
David
A:AnswerHi Arizona,
This AV receiver doesn't support zone 2 function. We recommend our STRDN1080 where you can set up two sets of speakers.
Hope this helps!
David
A:AnswerHi Clueless, thank you for your question. In order to control the receiver properly, you need to point the remote control at the remote control sensor on the receiver. Any obstructions between the remote control and the receiver should be removed. ~Earl
A:AnswerHi Joe,
Thank you for the interest! We recommend connecting wired speakers with a nominal impedance of 6 ohms to 16 ohms. We also recommend using speaker wires that are anywhere between 12 to 16 gauge. These are most commonly used for connecting speakers to an amplifier or an AV receiver
Regards,
David
A:AnswerHi mikeyP,
Thank you for the interest! Yes, we recommend connecting wired speakers with a nominal impedance of 6 ohms to 16 ohms. We also recommend using speaker wires that are anywhere between 12 to 16 gauge. These are most commonly used for connecting speakers to an amplifier or an Audio/Video (A/V) receiver.
Hope this helps!
David
A:AnswerHi John,
No, the STRDH790 doesn't support the speaker A+B and zone 2 functions. We recommend our STRDN1080. Take note that zone 2 component output jacks on the Audio/Video (A/V) receiver will output analog video signals only. To output a signal from the ZONE 2 jacks, the source device must be connected to one of the composite or component inputs on the A/V receiver.
Regards,
David
A:AnswerHi Al,
You cannot connect a wireless speakers to this AV receiver. We recommend connecting wired speakers with a nominal impedance of 6 ohms to 16 ohms. We also recommend using speaker wires that are anywhere between 12 to 16 gauge. These are most commonly used for connecting speakers to an amplifier or an Audio/Video (A/V) receiver. There is a speaker pattern wherein you can play all the speakers the same time and its called MULTI ST.
Hope this helps!
David
A:AnswerHi Jeff,
You can connect it to the center channel. See page 17 from this link for a sample diagram.
https://www.sony.com/electronics/support/res/manuals/4726/890436b47fd2ffcc4003f34dc5f2592c/47269051M.pdf
Regards,
David
A:AnswerHello SOUNDMAN,
Yes, this AV receiver supports 2 channel speakers. You can connect 7 speakers and 2 subwoofers. See page 41 from this link for more details. Select MULTI ST to output sound from all connected speakers.
https://www.sony.com/electronics/support/res/manuals/4726/890436b47fd2ffcc4003f34dc5f2592c/47269051M.pdf
NOTE: We recommend connecting wired speakers with a nominal impedance of 6 ohms to 16 ohms
Regards,
David
A:AnswerHi Customer,
No, you cannot connect Bluetooth speakers to this AV receiver. We recommend connecting wired speakers with a nominal impedance of 6 ohms to 16 ohms.
Hope this helps!
David
A:AnswerI have 4 ceiling/wall mount Polk Audio speakers in use with the receiver and they work beautifully. Your question also made me wonder if the receiver was bluetooth compatible. I found this on line "Not only can you connect to the STR-DH790 through Bluetooth® and stream all your favorite tracks, but with Bluetooth® Standby, you can turn your receiver on straight from your paired smartphone or tablet."
I hope this helps.
