A:AnswerHello Sarah,
Thank you for reaching out to us! Please know that the part of the Frigidaire 24" Front Control Built-In Dishwasher that goes inside the cabinet has the following dimensions:
Width: 24 inches
Depth: 25 inches
Depth with Door Open: 49 1/4 inches. If you need further assistance, feel free to ask!
- Owen
A:AnswerHello, LilMac1959. We appreciate your inquiry. Yes. This model of appliance is covered by a one-year limited warranty. We hope this information helps! - Christi
A:AnswerHello, Kathleen. We appreciate your inquiry. If you have not selected Max or Heat Dry and no LEDs are illuminated for these options, then the heater has been deactivated during the drying phase of the selected wash cycle. This is known as air drying. We hope this information helps! - Christi
A:AnswerHi sharon, thank you for your question. The Frigidaire Built-In Dishwasher (Model FDPC4314AS) is designed to fit a standard 24-inch dishwasher opening, but the required installation height is between about 33 1/2 inches and 35 inches based on the product specifications and installation guide.
If the opening in your rental measures 31 1/2 inches in height, that is lower than the minimum height required, which could mean the measurement may have been taken incorrectly, or the opening might include a removable toe kick or adjustable legs that allow more clearance. In many cases, dishwashers also have adjustable leveling legs that help fine-tune the fit during installation.
If your current appliance is already a 24-inch built-in Frigidaire dishwasher, most replacements of the same size category will typically fit the same cabinet space. However, the height of the opening still needs to meet the minimum installation requirement for the new model. You may want to re-measure from the floor to the underside of the countertop to confirm the actual opening height. — Reed
A:AnswerHi Tricia! Thank you for reaching out. For your Frigidaire dishwasher, model FDPC4314AS, the top (upper) spray arm can be replaced using the OEM part 5304506516. To replace it, first disconnect power and water for safety, then remove the top rack to access the spray arm. Twist or unclip the old arm from its mounting hub, align the new arm, and snap or twist it into place, ensuring it spins freely. Before use, clean any debris in the mounting area and run a rinse cycle to confirm proper operation. - Reed
A:AnswerYes, the Frigidaire 24" Front Control Built-In Plastic Tub Dishwasher (Model FDPC4314AW) offers both temperature boost options and drying features to enhance your dishwashing experience. - Jessica
A:AnswerHi there, SK. Thanks for reaching out. Based on available specifications for this model, this dishwasher does not include a sanitize cycle. It is a more basic model with core wash functions, typically including Heavy Wash, Normal Wash, Light Wash and Heat Dry Option. - Maria
A:AnswerHi, Pam! The Frigidaire FDPC4314AS dishwasher operates on a 120V electrical system at 60 Hz, which is standard for most household appliances in North America. This model is designed for use with a 120V AC power supply and is compatible with the 60 Hz frequency commonly used in the United States and Canada. We hope this answers your question. - Patrick
A:AnswerHi Davis, to install your Frigidaire 24" Dishwasher (FDPC4314AW), you'll need a dishwasher installation kit that includes the essential components for connecting the dishwasher to your home's water and electrical systems. These kits typically contain a water supply line, power cord, and necessary fittings. - Maico
A:AnswerHi there, valued consumer! No worries at all—that's a great question! When a dishwasher (like the Frigidaire 24" Dishwasher FDPC4314AS) is described as "built-in," it simply means that it's designed to be installed under your kitchen countertop and between your cabinets, so it becomes a permanent part of your kitchen layout.
So, unlike portable dishwashers or countertop models, a built-in dishwasher is a more permanent, flush-fitting appliance in your kitchen.
If you’re shopping for one or thinking about upgrading, I can help you compare features or check if it would fit your kitchen. Just let me know! - Maico
A:AnswerHi there, Jewels! It sounds like your Frigidaire 24" Dishwasher (FDPC4314AS) has the "Start/Cancel" light illuminated, which is usually an indicator that the dishwasher has finished its cycle, but the appliance may still be in a "ready" state, or there could be something else affecting the cycle.
It sounds like your Frigidaire 24" Dishwasher (FDPC4314AS) has the "Start/Cancel" light illuminated, which is usually an indicator that the dishwasher has finished its cycle, but the appliance may still be in a "ready" state, or there could be something else affecting the cycle.
Here’s what might be going on and how to fix it:
The constant "Start/Cancel" light could simply mean the cycle is complete, and the dishwasher is waiting for you to either open it or press a button to reset it. Try pressing Start/Cancel to see if that turns off the light.
1. Cycle Completion:
The constant "Start/Cancel" light could simply mean the cycle is complete, and the dishwasher is waiting for you to either open it or press a button to reset it. Try pressing Start/Cancel to see if that turns off the light.
2. Power Cycle (Reset the Dishwasher):
Sometimes, the dishwasher just needs a reset. To do this:
Turn off the dishwasher by pressing the power button.
Unplug the dishwasher or turn off the circuit breaker to the appliance for about 1–2 minutes.
Plug it back in or turn the breaker back on and press Start to see if the light resets.
3. Check for Errors:
If there’s a specific error with the dishwasher (like an issue with draining, water temperature, or door latch), the light might stay on as an indication. If pressing Start/Cancel doesn't help, consult the dishwasher's manual to see if the light corresponds to any error codes.
4. Door Latch Issues:
The door may not be fully latched. If the dishwasher detects an issue with the door, it may cause the "Start" light to stay on. Check to make sure the door is properly closed and the latch is secure.
5. Button Malfunctions:
Sometimes a stuck or malfunctioning button can cause the cycle to not reset properly. If that’s the case, try pressing all buttons to see if one feels “stuck,” or consider checking the control panel for any visible issues. - Maico
A:AnswerHi there! Yes, the Frigidaire 24" Built-In Dishwasher model FDPC4314AS is ENERGY STAR certified. This certification indicates that the dishwasher meets energy efficiency standards set by the U.S. Environmental Protection Agency, helping you save on energy costs while reducing environmental impact. - Maico
A:AnswerHi there, thank you for reaching out to us regarding your inquiry. We recommend reaching out to the local dealer for further assistance with the exact dimension of the box of the appliance.
- Jessica
A:AnswerMine has a ‘control lock’ on the panel. It’s for childproofing. It says hold for 3 seconds to lock or unlock controls. If you do not have this model then press and hold the ‘delay start’ for 3 to 5 seconds.
