Customer Ratings & Reviews

Upgraded to bi wire on my Martin Logan esl x and noticed a much better sound stage. Depending on your setup you may or may not hear a difference, but if your speaker supports bi wire then why not take advantage of it.

Poor Quality is all I can say. I purchased two sets of these and one was damaged and the other had a different set of banana plugs on it. Very displeased and wont be purchasing them again

I'm using these speaker cables to connect my new Marantz NR1605 A/V receiver to my B&W CM10 tower speakers and B&W CM5 bookshelf (surround) speakers. I bought two sets of these 10' cables as well as a single 8' cable for my B&W CMC2 center channel. So far, I'm very happy with these cables. They seem very well-made. Granted, no one really sees them, so appearance isn't really a huge issue, but they do look very nice and add a professional look to my home theater setup. Plugging them into the back of my receiver and speakers was easy with the banana style connectors. When it was all said and done I spent approximately $1000 on speaker cables and a subwoofer cable. I didn't take time to compare what my speakers would have sounded like with traditional speaker wire. However, everything sounds great... whether that's due more to the fact that I bought expensive speakers, or that I invested in good speaker cables, I honestly don't know... Most likely, it's a combination of both. I did do a lot of research prior to taking the plunge in buying all these Audio-Quest cables, and audiophiles say that good speaker cables really do make a difference... and comparing prices of the Rocket 33 series to some of the super high-line Audio-Quest products, $1000 seems like a bargain for my entire 5.1 system.

If your into audio and quality you might of used biwire jumpers which is better than the binding post jumpers speakers come with, after using speaker wire instead of the stock jumpers I was sold on an upgrade. This was one of the best upgrades I've done audio is much tighter. If you have mid to upper grade equipment highly recommend. Ps do the jumper wire hack first though

You know it is quality when it comes from Audio Quest. I purchased these cables to run my B&W CM9's. True twin 13 gauge long grain copper from amp to speaker terminals for bi-wiring. Sound quality is perfect. I can honestly hear zero distortion, even at high amp output. If you spent the money on top end amps and speakers don't go cheap on speaker cable.

Audioquest wiring never fails. Always had great sound quality from their products. Well made.

These speaker cables makes so much difference in sound quality. I noticed it clearly after replacing my X2 cables. Volume also increased a lot with these cables. All frequencies will be carried to the speakers without any delay from AV receiver. Overall the quality is amazing.

It is kind of expensive but if you’re spending some serious dough on a system it makes sense to do the same for the cables too. Just got some b & w towers and a center channel and I had to go with the best that was out there. You have to hear it with your own ears, and the quality is simply mind blowing! It’s definitely a must with high end equipment.

Super Cables, clear sound and good connections. Further more they looks good too :-)

nice looking cables cost a lot but nice and quick hook up

These speaker cables are completely neutral. They neither add or subtract from any audio signal that comes out of my tube amp. The radius of the banana plug’s cross section at each terminus of these cables is slightl too long for the jacks on my speakers. But they’re maleable enough that a patient Audioquest tech support rep.suggested I could use needle-nose pliers to easily compress them enough to fully seat them in the jacks And his solution worked beautifully. Excellent product. Great customer service.

If you own a pair of speakers that can be bi wired this audioquest speaker cable is definitely one to have. I hooked it to B&W 683 S2 and I notice the clean crisp highs and the midrange real came to life. Prior to no wiring the bass was not very evident but now I get a real nice flat and smooth bass. I would definitely recommend to bi wire your speakers. You will notice the cleaner and powerful sound coming out your speakers.

Love these cables, good quality and worth every penny.

I used this with my Bowers and Wilkins 702 and they sound amazing. I even biamp them as well.

Decided to upgrade our home theatre system and convinced myself not to be cheap with cables! Sound is great and I am very pleased with Best Buy's recommendation

The Geek Squad recommended these cables for B & W CM- 10 speakers. Very hard to knock the quality of the product.

Build quality is amazing, but you are still taking L and R channel's single signal to the speaker, I have done multi setups with Dirac on my Onkyo TX-RZ50 with my Klipsch RP-8000F II fronts and using the bi amp function on the amp can't be beat. True split high and low provides the best range of sound, only down side is you loose the Atmos speakers which I have found not to be a big deal even though they are the RP-500SAs. I will get an external bi amp and the the hights back. I will just get their regular cable to improve sound from external interference. Bottom line is $500 for cables that really do nothing or get a external bi amp for $1000 is a better deal.

These cables open up the sound of my speakers immensely.

Great sound improvement specially after going bi wire at the end of the speaker. Theyre also looks good as well without breaking the bank.

I went into these expecting only a slight difference. I got just that. It brightened up my speakers just a bit and gave a little extra clarity.