Customer Ratings & Reviews

Really great bang for your buck. Beautiful visuals, lots of room for large graphics cards, up to atx motherboards, and had no trouble fitting a 360mm aio. Works great, One thing that really s nice for me, is quick access to the back so I can easily swap out satas quickly. Just pops right off. Also great with cable management.

Beautiful case that is a breeze to build in. The included fans are bundled well and can be connected with two fan and A-RGB headers, one for the daisy chained side fans, and one for the back fan. These headers can also be disconnected and controlled separately if you have sufficient headers to accommodate them. If you are installing bottom intake fans, you will have reduced clearance on the bottom side of the motherboard to connect headers such as the front panel connector, but not so little that it can't be done. My biggest gripe with the case is the cheap PCIE slot covers. They are not removable other than by permanently yanking them off the case, which doesn't feel great and gives the case a cheaper feel than it otherwise would have. For this price point, ThermalTake should definitely include removable screwed-in PCIE slot covers. The rest of the case feels well built.

Beautiful case and relatively decent quality. Not too hard to put together. One issue we had is one of the fan blades were bent and it would catch on it self, we had to get a replacement fan put in. Another thing we noticed was the power on button light is a bit messed up and glitches. Makes for a good, sturdy case if all other issues are resolved and perfect for someone looking to decorate. (Note: Fan lights are not plugged in for the photos, lights do work for RGB fans)

Great pc case unique from others, plenty space in the back for cords ect and overall good design

I love this case! There's plenty of space for cable management and it provides lots of slots to feed the cables through, too. The color is so pretty and the tempered glass is such a good addition so you can look at your build. I had a black full tower case before this one, so downsizing was such a relief and it's honestly more than I dreamed of.

Perfect case for my first build! I absolutely love the blue it goes so well with the lights and everything looks so clean!

Good mid-case overall. I appreciate the PSU being mounted higher up in the back. Just wished it actually supported a 360mm AIO radiator. The side mount is too short which forces you to install it top mounted, which can cause long term damage to the AIO pump down the line. Also, the rear grates for the PCIe slots cannot be reinstalled. Once you remove them there is no going back, so you have to be 100% certain you're removing the correct one.

Great case, cable management is easy, looks amazing. Good price for a dual chamber case like this, only nitpick is the back pcie slots are breakaway

Very spacious and has a lot of ventilation, so it keeps my PC cool! The RGB lights are programmable with the lights on my water cooler, so it makes for a nice light show.

Solid Case all around, only reason it’s not a 5 star is that removing the PCIE brackets is incredibly unintuitive for a case at this price point

Love the case it's prefect and easy to clean and has amazing air flow

Beautiful and easy to build in case amazing buy I highly recommend

Great case, easy to build in! Super recommend for beginners, definitely also recommend getting a few extra case fans

Beautiful and it’s a great cuality I love it. Plus the colors

I recently built a PC for my son using this case, and while it's mostly great, there are a few important things to note. First, the brackets on the back of the case need to be broken off into the case itself. If you install the motherboard first, there won't be enough room to break these off afterward. My advice: remove these brackets before installing the motherboard. For the PCIe slots, slot 1 corresponds to the second bracket from the top, so leave the top bracket intact. You’ll need to remove the second and third brackets depending on your GPU. We went with a top-mounted 360mm AIO cooler (Thermalright Frozen Prism 360 Black) that expels air from the case. The three side fans are set up as intakes, and make sure to install the dust filter on the outside of the case behind these fans. We inverted the fourth fan (which is normally an exhaust) to push air into the case at the top, ensuring that cold air is directed at the top of the motherboard and the 360mm radiator. For our build, we used an Intel i5-4600K processor and an MSI Tomahawk MAG B760 DDR4 motherboard. Idle temps are around 29-30°C, which is excellent. The four intake fans create a positive pressure inside the case, preventing dust from getting in. We didn’t install additional fans at the bottom of the case, but when you receive the case, there will be a dust filter at the bottom. We removed it and placed it behind the three intake fans. I also picked up extra magnetic dust filters, which we attached behind the fourth fan. The cables that come with the case (for fans, ARGB, etc.) are more than long enough, so you won’t need splitters, hubs, or extension cables. When routing cables, here’s a tip: pass all the wires to the front of the case before installing the motherboard. Some wires go through the bottom, some through the middle, and a few up top. Specifically, make sure to route the two 8-pin CPU power cables from the PSU to the top of the case and connect them to the motherboard *before* seating the motherboard. This is a bit unconventional, as we usually install the power supply last, but this step will save you a headache later. For fan control, we connected each of the four intake fans to separate fan headers on the motherboard so we could control them individually. The ARGB fans are already daisy-chained, so only one ARGB header is needed. Once the build is complete, the back of the case will have quite a bit of untidy wiring, but there’s a lot of space to tuck it all away. We only used cable ties at the front to organize the two AIO cables (Pump_Fan1 and CPU_Fan1). No cable ties were needed at the back. A quick tip: wear latex gloves while handling the tempered glass, or you’ll leave fingerprints all over it. Lastly, the power supply is mounted midway up the case, which works out well because there’s plenty of cable length to reach the 24-pin, the two 8-pin CPU connectors, and the GPU header. Just remember to pass those two 8-pin connectors through before you install the motherboard! Lastly, the case looks amazing—not too big, not too small, just perfect. The two-sided tempered glass looks very elegant. Very lastly: Do not try to fit a 360 aio on the side (where the 3 intake fans are). It will NOT fit.

I've had this case for two months now and I'm absolutely obsessed with how it looks. The color is accurate to the online photos and it's very easy to build in with several cable tie points and nooks to tuck away bulkier cables. Gives you plenty of space for different configurations and for decorating inside. Please keep in mind that it is a very wide case so if space is a concern then I would opt for something smaller. Build quality is solid and I'll definitely be keeping it for many years and upgrades down the line. Airflow has been excellent as well which is something I was concerned about with a "fishbowl" case. The only con I can think of is that the power button LED is quite bright and you can see your cables from the metal side panel when the RGB fans are powered on.

Great white case. Has all your needs. Very aesthetically pleasing. Thermaltake case are the most beautiful! Could use another USB and usb-c on the front panel but that is very minor.

It is a wide body, but houses everything well and plenty of spaces to route wiring. Needed a shorter case for my desk and this worked perfect.

10/10 case , the color is beautiful. It isbig but its soo nicee . I LOOVVEE ITTT!!

Just changed my pc case to this one & it’s even more beautiful in person. I love it.