1-10 of 45 Answers
Jbuds air left keep blinking not connect to jbuds air right
Sorry, there was a problem. Please try again later.1st, disconnect so it doesn't connect automatically again. 2nd, put the earbuds inside and leave the charger case opened. 3rd, press one earpiece 4 times quickly and you'll see a blinking blue light. 4th, Repeat the other earbuds; press earbuds quickly 4 times quickly until a blinking blue light shows. Does not matter what side you do first. 5th, take both earpieces out and keep then from a far 2 inches and they should pair together. 6th, the L earpieces should be a solid white light and the R should be blue/white before connecting again to Bluetooth if you did it right. If the L is still blinking, just repeat steps 2-5 again. Last if it didn't work or you did something wrong, just repeat the whole process again as I had the same problem and it automatically fixed my problem. P.s I've read the manual that I had in my box- Troubleshooting section. https://www.jlabaudio.com/pages/manuals your's in the JBUDS Air v2 if your wondering.
Sorry, there was a problem. Please try again later.The left JLAB Executive Air earbud will only blink blue one long blink followed by 3 medium length blue blinks compared to the 4 rapid blue blinks of the right ear bud when trying to pair the earbuds to one another. The right earbud works just fine every time, and I can pair it to my mobile phone with it working just fine... just noooo luck in all of these posts and videos getting the left ear bud to work at all. Again: the left ear bud blinks one-long-blue-blink followed immediately by 3 medium-length-blue-blinks with no other results. The case will not illuminate a blue light in front of the left ear bud while the right ear bud illuminates a blue light in front of it. Three white lights on the case properly indicate a full charge.
Sorry, there was a problem. Please try again later.I am having same problem with my left earbud. I have tried all answers you received and nothing in left erbud. I dont even get a charging light on my case for left earbud. I need help too.
Sorry, there was a problem. Please try again later.I searched high and low for an answer on how to get my left earbud working again, and FINALLY found the answer posted by JLabs here. I followed their instructions and both earbuds are now working!
Sorry, there was a problem. Please try again later.This works! I searched and searched. This one did the trick How to Sync JLAB headphones? GO Air Keep earbuds in charging case and forget "JLab GO Air" from bluetooth device settings. Quick tap one earbud in the charging case 7x. Earbud will flash blue 3x. Quick tap the other earbud in the charging case 7x. ... Take the earbuds out of the case. ... Now you are ready to connect to your Bluetooth device. https://www.jlab.com › help-center JLab
Sorry, there was a problem. Please try again later.Don’t get excited. I do not have the full answer yet. But here’s an idea. My lights weren’t corresponding with any of the suggested methods. Like at all. Upon frustration I held the stem of the non working bud down into the fully charged case. The lights changed (yay) up until I gave up holding it in. Because who wants to sit there and hold an earbud in the case until it fully charges? Not me. Anywho. I figured this nonsense might be a charging plate issue. So what I did was remove ANYTHING that would act as a buffer (for charging). I took off the ear cushion ring thingy. And I even took off the ear tips. I basically stripped the earbud of its....’dressing’ (if you will). Placed the jammies back into the charging case and now the lights are doing what they are supposed to do. I will wait until the non-working bud finally gets a charge (or at least responds) then give an update. But try stripping the earbud so it can sit snuggly inside the charging case. I hope this helps.
Sorry, there was a problem. Please try again later.Okay, so after a couple of hours trying everything I could find to fix it, I gave up, then tried it one more time: * First, I turned off & forgot all Bluetooth it connected to. * I took off both earpieces & cushions, let it set in the charging base for a couple minutes, tapped each 7 times, right then left, then let it set for 10 seconds. * Bluetooth still off, take the earbuds out of the case [mine were still blinking separately from each other]. I held both buttons for 10 seconds & they blink off. * Tap them again to flash them on, then tap 3 times & hold until they both flash, & they should both be flashing blue & white, then they start blinking white more in sync, until they're paired to each other. * Turn on Bluetooth, & they should both connect when you pair it to your device. Good Luck!
Sorry, there was a problem. Please try again later.Mine seems to be the older version (v1?), because I bought it 3 years ago and the press 4 times method didn't do anything. But, the left ear bud worked after I followed the steps described in this youtube video -> https://www.youtube.com/watch?v=JQBFC9kKaAg Basically: 1. Turn off/disable all bluetooth devices 2. Turn off both earbuds (hold button for 3-5s) 3. Press both eardbuds, hold for more than 10s. I think I hold mine for 15-20s. Both eardbuds will turn on (they'll say "hello"), but keep pressing the button for another 15s, and they'll blink blue-white whatever. 4. You'd know the left ear bud has paired if the left ear bud light stays on with white color. 5. Enable bluetooth device and reconnect. Good luck!
Sorry, there was a problem. Please try again later.Yeah it seems I have the same problem as everyone. The left ear bud just will not connect. Gonna be returning these at first opportunity.
Sorry, there was a problem. Please try again later.