See more imagesRating 4.8 out of 5 stars with 28 reviews
would recommend to a friend
DavidJr Posted
What I mean by easy is that there are only 4 lag bolts and 4 nuts on the back of the TV and you are there. However, you need a stud finder, a drill and 7/32” or there abouts drill bit, ½” socket and a level for the wall part and then smaller socket pending the nut that fits your TV as there is a variety available. Don’t force them as there is likely one that fits perfectly. Once you find the studs you can hang the handy template on the wall with a thumbtack or something, level it out, mark the spots, drill the holes, then hold the actual bracket up on the wall and drill in the lag bolts. Did it all alone in about half an hour. The directions start with putting the bracket on the TV, but I wanted to take a shot at what it looks like without the TV blocking everything. Even if you don’t get it perfectly level, there are hex screws on top that you can use the included hex key and make minor adjustments. There are tension screws to control the tilt and the brackets allow for a bit of rotation, but you are still fairly limited on how much rotation and tilt compared to some other style of mounts. You can even shift right or left several inches if the studs weren't the perfect center for you. Once everything is in place, just hook the TV on the top bar, it rests and locks in on the bottom and you are watching TV before you know it. It rests fairly close to the wall, but enough space to still allow cables if you don’t go the fancy route and hide them in the wall. To take it off there is a clip at the bottom of each side and it comes off just as easy, but there is also a whole for putting a pad lock if you don’t want someone taking it off that easy. Overall, simple design that allows for 7-12 degrees of tilt, a little rotation and up to an inch of lift while keeping the TV a bit over 2 inches from the wall. Quick easy install even for 1 person.
TechBuyer Posted
SANUS makes the best TV wall mounts and a number of other quality home theatre mounting hardware. The Elite line-up is their step up from the more pedestrian line, where everything is just slightly better, nicer, and engineered with that next level of quality. The 4D Tilting TV mount for 48-100" TVs is a slightly upgraded version of the massively popular and highly rated mount for 42"-90" TVs. I'm not sure what the exact differences are but from previous research on my Sanus products usually this means slight changes to handle the larger size and making sure the hinges, springs, and frame can bear the additional size and weight. The other thing with mounts of this size and quality is that they MUST be lag-bolted into studs for larger TVs. Do NOT try and use drywall anchors for TVs that are on the high-end of the size and weight spectrum. The best part about these Sanus Elite products in this range is that they offer mounting slots that can let you hit a stud anywhere along with the TV frame. The quality on this Tilting TV mount are unparalleled. Everything slides so easily as if it was assisted and the hinges and scissor extensions are super sturdy and do not feel unstable or cheap. The only minor downside of these extension type TVs is that they are not as flush to the wall as some of the slim designs. The major benefit however is undeniable, the ability to pull the TV away from the wall to plug in cables, make adjustments, or make any adjustments. I know everyone has had that moment where they realized they didn't plug in an HDMI cable and needed it and its a hassle to try and plug a cable in or to take the TV off the wall. I personally recommend buying enough HDMI cables you need at once and then plugging them all in, then pulling them through a wall if you need to at the same time. I personally don't use the side to side tilt, or the up and down tilt. I just tilt down slightly to limit glare and to direct focal point to eye level sitting on a couch, but I don't like the aesthetic of pulling the TV off the wall and then aiming it with massive tilt downward. If you need a quality mount that you only have to deal with one time for as long as you live at your home, choose Sanus. It is worth the investment to have this in that spot forever and realize as long as your TV has 400x400 VESA mounts and is within the size range, you don't need to replace your mounting hardware, just your TV when the time comes.
Ace254687 Posted
The Sanus Elite 4D wall mount is a fantastic wall mount that works and looks great. The mount comes with everything you need to mount it on your wall. There is a QR code on the box that is supposed to give you installation videos, but I guess this mount is too new because it’s not listed anywhere in the products. If you have any experience installing TV mounts, this is not that much different. Installation is pretty straight forward, and the instructions are easy to follow. The quality of the mount is great; it’s made of good quality materials that are strong and heavy duty. I love that the frame on this mount is open and wide, this gives you plenty of room for installing it over electrical outlets, or an in-wall electrical box. Once everything is installed correctly, the mount is able to extend outward almost 7”. This gives you plenty of room if/when you need to get behind your TV for cable/power management. The mount also tilts forward a generous amount, giving you the perfect viewing angle. I installed a 75” Sony TV, that weighs about 95lbs. So, I was extremely surprised at how easy it was to tilt it, swivel it and extend it with very little effort. Yet, the mount is able to hold it steady no matter which position or angle I move it to. The mount does have a low profile, meaning my TV doesn’t stick out of the wall very far, making it look really clean. Overall, I am really impressed with the Sanus 4D Advanced Tilt wall mount. The build quality is outstanding and it functions perfectly. I love how little effort it takes to tilt/move my 95lb TV, and it holds it perfectly in place without shifting. The ability to extend your TV is essential, as it allows me perfect access to get behind it for cable/power management. I would highly recommend this to anyone looking for a new TV mount.
Ssmithcrew Posted
We recently installed the SANUS Advanced Tilt 4D TV Wall Mount in our living room for our 75-inch TV, and we couldn’t be happier with how everything turned out! The installation process was pretty straightforward. The instructions were easy to follow, and the hardware provided made the setup go smoothly. We took our time locating the studs, getting the mounting plate level, and making sure everything was securely attached before hanging the TV. Once the TV was mounted, the 4D adjustment features were a really nice bonus. Being able to tilt and adjust the TV made it easy to find the perfect viewing angle for our living room and reduce glare. The mount feels solid and well built, giving us confidence that our large TV is safely supported. I also appreciate the extra access behind the TV for connecting cables and making adjustments. The finished setup looks great and gives our living room a clean, modern look without taking up any floor space. Overall, this is a high-quality mount that was worth the investment. We are very pleased with the installation and performance and would definitely recommend it to anyone looking to mount a larger TV!
Michael Posted
When I purchased my house in December, I had a standard wall mount over my fireplace for my 75" TV, but discovered it had limited features. It only allowed the TV to stay in one position which put the center of the TV above eye-level. Welcome to the Sanus 4D Tilt Wall Mount! Installation is easy - simply place the TV face down on a soft surface and attach the brackets using the included hardware. Attach the wall plate to the wall studs (accommodates spacing up to 26" wide) using the 4 included lag bolts, making sure it is secure and flush with the wall. Grab a partner and carefully lift the TV onto the top brackets and then slowly push the bottom of the TV against the brackets until you hear a "click" indicating that it is secure. You can adjust the TV right/left by sliding it on the bracket and adjust level with the screws on the top of the bracket. You can then pull the TV (carefully) away from the wall and adjust the up/down tilt. Because the scissor-like bracket allows you to pull the TV away from the wall, there's no more fumbling while trying to connect your inputs and power cord! It sits less than 3" from the wall, extends outward up to 6", and supports TV's up to 150 lbs. It swivels right/left up to 15 degrees and tilts from 12 degrees down (making it easy to see from the couch) to 7 degrees up. And because it extends outward, you can tilt it down without it hitting the wall! The scissor-like bracket allows for smooth movement in any direction.
Linksys Posted
This is my second Sanus mount and I’ve been impressed with not only the quality of both but the innovation. The 4d feature was the biggest draw for me as this is replacing the same type of mount but without these features. I’m currently using a flat mount as I don’t need full motion and I like how the flat mounts keep it closer to the wall. With the Sanus 4d I get the best of both worlds. I get the closeness of a flat mount with motion similar to a full-motion mount. I’m obviously not getting as much articulation as a full motion would give but in my case I don’t need it. Having the ability to extend the tv out and tilt it left and right a little is a huge benefit for me. The biggest pain with most flat mounts is adding or adjusting cables once the tv is installed especially if it’s a big tv, this model completely eliminates that problem. With a weight capacity of up to 150lbs and up to 100 inch tv, it future proofs me some as I’m currently using this with an 85 inch tv. I also like the fact it has a leveling feature built in, so if you were off a little when you secured it to the wall, this will allow you make it level with this feature. I’ve mounted many TVs and sometimes I've had one or two that were just a fraction off so having the ability to adjust it is really nice. If you want the closeness of a flat mount with some of the added benefits of a full motion, the Sanus 4d is a great option.
PhillipB Posted
This SANUS Advanced Tilt 4D TV Wall Mount for TVs 48"-100" is pretty easy to mount and use. Color is black. Being behind the TV doesn't matter to me on color. So installation is key to everything related to TV watching experience. Placement in the room and height are super important. If too high or low and you watch for long duration will cause neck or shoulder strains. Also overall placement will affect room ambiance etc. Also comes with all of the bolts etc needed for installation Also make sure you have someone help you lift and move the TV so you don't mess your body up with a super heavy TV. All this to say. Make sure you place your TV correctly and to your satisfaction. The mount has a template... Yay.... This helps A LOT. So you don't have to drill multiple holes etc. After you mount the TV. Use is really easy. Up down left right are all easy to do to maximize viewing angles. It works for my TV. From easy installation to easy use. I can't complain. I would recommend this Mount for what it advertises for.
HoMi3 Posted
I love when a product is easy to install and it just feels like you upgraded your whole room by getting your TV mounted and off your furniture. Sanus has been around for a while and they have a whole range of products that can mount your TV any which way you can dream. This "Advanced Tilt 4D Wall Mount for TVs 48-100 inches" is probably the sweet spot for many households who want to claim back some furniture space and gain the added benefit of tilting your TV to eliminate glare or aiming for best seating position. Upon opening, the instructions are to scan the QR code to better see the manual online. I was taken to the Sanus page but this particular model number was not listed on their website.. so I was left with just doing this on my own. No problem, I am pretty handy but I wanted to confirm based on my TV's size and dimensions, what was the best height to mount this TV mount? I played with their calculator and used an alternative model number that seemed close enough and I was able to get a precise measurement after putting in my TV model number. It sure is nice to have this feature. A few lag bolts into my studs that I had marked, got it nice an leveled, and then mounted the hardware to the back of the TV, and we were in business. It has such a good amount of tilt all around and it just feels so solid. If you are interested at all in having tilt features to eliminate screen glare and want to just have better viewing angles on your TV, look into getting this mount. It is easy enough with a few home owner tools to install on your own too. The hardest part was lifting my heavy 65" TV. But once installed, I ask why didn't I do this sooner?
Sanman Posted
What a breeze to install. I mounted it on drywall, after using a stud finder and level marked the spots and drilled pilot holes. Lots of hardware included in mounting kits so you will have all the hardware needed for most installations. After mounting bracket to wall you can fold down the covers to hide mounting hardware (nice). Then came mounting the other part of the bracket to the tv there again are various bolts to mount to tv depending on size and depth of your tv, so be careful not to use to long of screws for will definitely cause damage to your tv. And don’t torque the bolts too tight. When mounting tv to wall mount get help to mount tv to wall bracket You need to tilt tv at a slight angle to slide onto the tracks. You can put a level on top of the tv and turn the adjacent screws till level, then lock into place. This is a nice childproof feature. Pull away from the wall and connect all cables and zip-tie them too bracket to keep from pinching the cords. The tv really sits flat against the wall. Wife approved. It is adjustable to any viewing angle in the room left to right and up and down. Very strong and stable bracket when stud mounted will hold with any size and weight tv Highly recommend bracket and great quality and build.
Kathy Posted
This is awesome! It does everything! The Geek squad installed it with my new Samsung 85” tv and I’m beyond pleased! Thank you
Dexter Posted
Ordered a S95H and was able to use this wall mount to easily install it on the wall highly recommend
taxpayers Posted
It was easy to mount and had good instructions. The screen tilts in many directions.
exactlywhatineeded Posted
Pretty slick mount. Just enough tilt and swivel for a large TV
Patrick Posted
I am writing this review for the SANUS Advanced Tilt 4D TV Wall Mount for TVs 48"-100”, Model BLT4. I purchased a Sanus wall mount for a 50” TV a few years ago and have been fairly pleased with it. My only complaints with it are of my own making as I was trying to be frugal at the time and bought one that was limited in its available options. The quality of the mount is quite remarkable, and has never given me any issues whatsoever. I have a much larger TV, and have been quite hesitant about mounting it to the wall because of its weight. But when I saw that Sanus had a premium mount available for TVs 48”-100”, I decided to go ahead and throw all caution to the wind. And I think I may be like most on this point, none of us want to mount a TV to the wall just to have it fall later on because of a cheaply built budget wall mount. And like I said, my other Sanus wall mount has been outstanding, and that is the only reason I decided to go ahead and mount the 75” TV. It was a bit surprising when the wall mount arrived at my house. I suppose I was expecting it to weigh a lot more, but I was able to lift it quite easily. I am not a good judge of weight, but I’m guessing it weighs between 20-25 pounds. After bringing it inside, I decided to go ahead and “git ‘er done.” Unboxing the mount was a breeze…just cut some tape, open the flaps, and that was it. The box comes with instructions, an amazingly designed template that immediately makes you think, “It doesn’t get any easier than this!”, all the hardware, and of course the mount components. I took a moment to browse the instructions and was very happy to see that the entire process appeared to be quite simple and easy. Now this is where I am going to interject the only negative thing I have to say about this particular model. The front page of the installation guide states you can scan the QR code and use the Sanus “Height Finder” to determine the optimum height to place your TV. However, as of this writing, the Height Finder does not include instructions for this BLT4 model, which is rather disappointing as I really wanted to use it. But like I said, this is the only negative thing I have to say about the BLT4. The mounting process calls for several tools, and to be sure, you will need every one it lists to make the installation quick and easy. Before beginning I took and inventory of everything that was needed, went over the instructions a couple more times, and went to it. Again, my kudos to Sanus for the brilliant mounting template. My advice? Don’t take any shortcuts, follow the instructions, and most of all don’t try to level by eye, use a level! There is nothing more frustrating than finishing something up only to find it is off-center or off-level. All in all, after beginning, I had the wall mount installed and ready to use in less than 30 minutes. This included mounting the hanging brackets on the back of the TV. I called my neighbor to come over and help me lift and mount the TV, and in a few minutes the entire process was finished. All that was left now was to replace all the cables. And this is where the BLT4 shines, and makes me ashamed of myself for buying a budget mount the last time. Before, with the old mount, attaching cables was sometimes a bitter experience, mostly because I could not move the TV away from the wall to see what was behind. I couldn’t see where, let’s say, the HDMI cables went, or the ports for the soundbar, and so on. Several times I had to actually remove the TV and then replace it, typically after an eternity in trying to insert a cable blindly. The BLT4 has a telescoping feature that allows the mounted TV to not only move away from the wall, but to swivel outward as well. I was almost giddy as I began reattaching cables into their respective ports, it was so freaking easy, and I didn’t need a flashlight or camera (if you have ever had an experience like I just laid out above, you will know exactly what I mean). Even now, several days after mounting, I still chuckle to myself about how one or two added features can make such a huge difference to the overall experience. Again, THANK YOU SANUS!! As you can tell, I am 100% completely and wholly satisfied and pleased with the SANUS Advanced Tilt 4D TV Wall Mount. I am absolutely sold on the Sanus brand, and I will never buy any other brand of TV mounts ever. If you have or are contemplating the purchase of a larger TV but are worried about mounting it, don’t be… just get the BLT4!
BillnMish Posted
Sanus is one of if not *the* main player in the TV mount realm, so right off the bat, regardless of price-point, you know you're going to get a solid product. The peace of mind their name brings to your purchase is priceless, you just know that documentation, build quality, features (relative to the money you're spending) are going to be amongst the top or standing alone at said top compared to the competitors. With this particular Sanus Elite model, the BLT4-B1, you're capable of handling a rather massive range of TVs: 48" up to 100" and anything up to 150 lbs. Don't think I've seen a TV that weighs that much on the market since the 90s but hey, nice to know what it's upper limit is! Independent of the mount itself, it needs to be said that if you are going towards those upper limits in size/weight, that you *must* ensure you're hitting studs when anchoring the unit. Going straight into the drywall, even if you anchors, is *never* a good idea and definitely not worth the risk of damaging your $$$$$ TV - not to mention anything else in the vicinity that will get destroyed during the fall. Alright, with all that out of the way... Installation is very well documented and all materials are provided (sans tools). Follow the steps, use the guides, wham bam you'll be up and ready to throw your TV on it in 20 minutes. There is a level built-in so no need for reaching for one of those. Again, Sanus thinks of all the little things to make your "job" as easy as possible. Gotta love it. Movement is easy in all directions and extremely smooth. It is *not* a full motion unit, but you still have a good amount of extra degrees and inches of range beyond a "standard" model. Your down, left, and right are capped at 12 degrees and your up is limited to 7. Self-explanatory, but you can't push it completely flush, you have ~2 inches of material keeping you from going flush. And pulling it all the way out you have nearly 7 inches of extension. If you're in the market for any tv mounts, Sanus should always be one of the first brands to explore. And if you have a TV that fits the specs of what the BLT4-B1 is offering, I can't recommend it enough.
Titan5178 Posted
I have installed a lot of TVs on SANUS mounts, so I’m very familiar with their lineup and installation process. This model is an advanced tilting model, providing a bit more movement than the standard tilts but not as advanced as a full motion mount. This model comes with a large frame that is attached to your wall with 4 lag screws, and they also provide brackets and an assortment of screw sizes for your TV and a few spacers if necessary. Once it’s installed you can tweak it in nearly any direction hence why SANUS markets it as 4D. While you can fine-tune both the height and rotation (level) of the TV it’s the tilt and swivel that are the true four dimensions of free movement. It can retract to just 2.2” from the wall out to 6.8” and can tilt down 12 degrees or up 7 degrees, and swivel 12 degrees left and right. Ideally, I would have tested this with a 100” TV, but I don’t have one yet. I’m using it with a modest 55” older TV for now that’s probably nearly as heavy as one twice its size and so far I like how it is sits when mounted. This TV is near a corner and mounted high so having the extra tilt and space from the wall allows me to angle it more towards the center of the room. There are not really any downsides except to make sure to get the right mount that you need. Even though this is one that tilts further than their more basic models, it’s not a full motion mount. Those allow you to extend over a foot from the wall and offer even more swivel and tilt, but are more expensive. Likewise, if you have a much smaller TV, and do not plan to upgrade, you could buy a cheaper SANUS mount, but I’d really recommend just picking this one up unless your TV is less than 48”, the minimum that this mount supports. Pros: - Works with TVs up to 100” - Great instructions - Includes mounting hardware - Comes with screws for tv mount - Paper mounting template provided - 150lb weight limit Cons: - Not a full motion mount Overall – I think I have a SANUS mount for every TV in my house, and this model is one of their better ones that gives you a bit more freedom to tilt the TV perfectly towards you.
Tweed Posted
Overall, I’m impressed with the SANUS VLT7 TV mount. It feels like a well-made product designed to make mounting a large TV easier and give you more flexibility once everything is installed. It’s not the cheapest option out there, but the features and overall design make it worth considering if you want something a little more substantial than a basic wall mount. Pro 1: Easy to adjust the TV One of the best things about this mount is how much flexibility it gives you. Being able to tilt the TV helps reduce glare and makes it easier to get a comfortable viewing angle. It’s also nice to be able to pull the TV away from the wall when you need to get behind it to plug in a device or change cables. These little conveniences make a big difference, especially if your TV is mounted in a spot that would otherwise be difficult to reach. Pro 2: Solid construction and a clean look The mount feels like a good choice for a larger TV, and I like that it keeps the television relatively close to the wall when it’s pushed back into place. It gives the room a cleaner look and frees up space that would otherwise be taken up by a TV stand. The adjustment features also help make it easier to get the TV straight and properly positioned. Overall, it’s a practical design that balances strength with a nice finished appearance. Con 1: More expensive than basic mounts The biggest downside is the price. There are plenty of cheaper TV mounts available, and if all you need is something to hold your TV in one position, spending extra on this model might not make much sense. The additional adjustment options are useful, but not everyone will need them enough to justify the higher cost. All things considered, the SANUS VLT7 is a good option for anyone who wants a sturdy, adjustable mount for a larger television. The ability to change the viewing angle and access cables without too much hassle makes it more convenient than a basic mount. While the price may be a little high for some people, the extra flexibility and clean appearance make it a worthwhile option if those features are important to you
SUHD Posted
This weekend I had a chance to install the SANUS Advanced Tilt 4D TV Wall Mount in the living room above the fireplace. The incredible versatility and adjustability of this mount allows the TV to be installed pretty close to the wall at only 2.2”. It can extend, tilt and swivel to a much better viewing position and angle. It is made of quality steel and feels very solid and gives you the confidence it can safely hold the 150 lbs weight listed in the specs. My 77” Sony OLED TV only weighs about half that, so it’s super sturdy on this mount. Installation was much easier than I’ve experienced with other lower-end brands even though this is a heavier, more advanced mount. That’s because the instructions it came with are very well written and the included wall template was easy to use. Moreover, it came with all the necessary bolts, spacers, hardware and extras to cover a variety of TV sizes. Make sure you have these tools ready to guarantee the best install: Tape Measure, Pencil, Stud Finder, Level, Power Drill, Philips Screwdriver and socket wrench. Once installed, if you didn’t get it perfectly leveled, there is an adjustment screw that will help you adjust it to perfection. It is fairly low profile, only 2.2” from the wall that makes it look nearly flush mount especially above the firewall mantle that’s sticking out about 6” from the wall anyway. Despite that, it still offers easy adjustments - extension mechanism up to 6.8”, left to right 12 degrees swivel and tilt up 7 degrees and the most importantly tilt down 12 degrees for best viewing angles to minimize glare, etc. Additionally the built-in cable management helps hide the power cord and HDMI cable very neatly. This SANUS Advanced Tilt 4D TV Wall Mount is truly built from solid, premium materials that should last the test of time and to that end it also comes with a 10-year warranty.
MichaelM Posted
You might think that all TV wall mounts are about the same. That's pretty much what I thought before I got the SANUS Advanced Tilt 4D Premium TV Wall mount. If everybody mounted their TVs at eye level that might be the case. But if you mount your TV above a fireplace, like we wanted to do, having a mount that not only tilted but also kept the TV as close to the wall as possible was a must. This mount definitely does the trick. While keeping the TV only 2 inches from the wall (center of TV), it also allows for up to 12 degrees of tilt, plenty for our needs. The mount is also well-made and feels sturdy and secure. That's good, because it's rated for TVs up to 90". Just pay close attention to the mounting guide and make sure you install the brackets where studs are located. One of the features I love the most is the Proset feature. Getting things level is very important to me, but it can be hard to do when mounting a TV. If you don't get it perfect when you install the mount, no worries. Proset offers up to 1 inch of adjustment, even after the mount has been installed. That's a feature all TV mounts should have. Not only does the mount allow for tilt, but it also allows for up to almost 7 inches of pitch. This allows you to extend the TV out to make all the connections you have comfortably. An added advantage is that you can also extend it to avoid glare. Lastly, this TV mount also has brackets for a sound bar that moves with the TV is you change the pitch. And it's height adjustable. Overall, this is an extremely nice TV mount. It's more expensive than mounts I've purchased in the past, but I believe the build quality and added features make it worth the price.
TrueReviews20 Posted
SANUS mounts are the best on the market in my opinion. They are well designed, come with the right parts, and are typically good quality. They are not as high quality as 10 years ago but given the expansive options available these days, they are a reliable brand that can be trusted. Who should buy this: You have a good quality TV with anything but the most simple mounting requirements. If you're putting up a garage TV or maybe a bedroom, you don't need this unless you have unique circumstances. This is not a full motion extension, so if you need a lot of flexibility, this is not it. Why I like it: It allows me to mount the TV easily, manage wires and connections better, and has flexible adjustments that can help with the intricacies of mounting a TV. Gone are the days of an empty wall in which you just needed a basic tilting mount. Between fireplaces, window glare, and height issues, adjustability is key. The bigger your TV, the more beneficial this mount will be. You can pull the TV out just enough to give you the full tilt. I've found that it also gives it a better floating appearance while not popping out too much. I don't think there's any use detailing the installation. It comes with everything you need and the instructions are fairly straightforward. If you don't know what you're doing, definitely hire someone. In summary, this is another great option from SANUS and I highly recommend it.