The AT-LH11H is a universal ½"-mount aluminum headshell that weighs only 11 grams – the lightest in the LH series – allowing it to be used with a wider range of cartridges on more turntables and tonearms than the other models.DesignWith its non-threaded through-holes the AT-LH11H is ideal for mounting cartridges with threaded mounting holes such as the AT-OC9X AT-ART9X and VM95 Series cartridges. Like all LH models this headshell has a hard anodized finish that reduces unwanted vibration and comes equipped with OFC (oxygen-free copper) lead wires. It also features an adjustable cylinder that enables precise azimuth and overhang settings. The headshell includes cartridge installation screws plastic washers and a hexagonal wrench.LH SeriesThe headshell is also available in 13-gram (AT-LH13H) 15-gram (AT-LH15H) and 18-gram (AT-LH18H) models for optimal compatibility with your cartridge/tonearm requirements.What's in the BoxATLH11H Aluminum HeadshellInstallation HardwareSpecificationsWeight: 11 grams (0.4 ounces)Mount: Universal 1/2" mountMaterial: Lightweight aluminum constructionLead Wires: Oxygen-free copper (OFC) lead wiresFinish: Hard anodized finish to reduce unwanted vibrationAdjustable Cylinder: Allows precise azimuth and overhang settingsCompatibility: Ideal for cartridges with threaded mounting holes such as the AT-OC9X AT-ART9X and VM95 Series

The AT-VM95C/H combo kit includes the AT-VM95C dual moving magnet cartridge premounted on the AT-HS6BK headshell. VM dual magnet cartridge with 0.6 mil conical stylus. Aluminum cantilever. Specially wound coils increase output voltage. Durable low-resonance polymer housing. Threaded inserts in cartridge body enable cartridge to be mounted to headshell with just two screws – no nuts or washers required. Compatible with any AT-VMN95 replacement stylus. Universal ½"-mount headshell for 4-pin turntable cartridges.

The AT-VM95E/H combo kit includes the AT-VM95E dual moving magnet cartridge premounted on the AT-HS6BK headshell.FeaturesElliptical Bonded Stylus on an Aluminum CantileverDual Moving Magnet DesignDurable Low-Resonance HosingHigh Output Level (4.0mV)VM95 SeriesThis VM95 Series cartridge with 0.3 x 0.7 mil elliptical stylus fits half-inch mount turntables. The cartridge’s special coil design delivers a powerful output level of 4.0 mV. It also offers excellent channel separation and low distortion for outstanding tonal quality. The durable low-resonance housing includes threaded inserts that enable the cartridge to be mounted to the headshell with just two screws – no nuts required. And since all VM95 Series share the same body the stylus can be replaced with any of the six interchangeable AT-VMN95 replacement styli.What's in the BoxAT-VM95E/H Headshell & MM Cartridge Combo KitInstallation HardwareSpecificationsFrequency Response: 20-22000 HzChannel Separation: 20 (dB at 1 kHz)Vertical Tracking Angle: 23°Vertical Tracking Force: 1.8-2.2 g (2.0 g standard)Stylus Construction: Bonded round shankRecommended Load Impedance: 47000 ohmsCoil Impedance: 3.3 k ohms (1 kHz)DC Resistance: 485 ohmsCoil Inductance: 550 mH (1 kHz)Output Voltage: 4.0 mV (1 kHz 5 cm/sec.)Output Channel Balance: 2.0 dB (1 kHz)Stylus Shape: 0.3 x 0.7 mil ellipticalCantilever: Aluminum pipeStatic Compliance: 17 x 10 – 6 cm / dyneDynamic Compliance: 7 x 10 – 6 cm / dyne (100 Hz)Mounting: Half-inchDimensions (Cartridge & Headshell): 0.84" x 0.83" × 2.46"Model: AT-VM95E/HMounting Feature: Half-inch mountRecommended Load Capacitance: 100 to 200 pFReplacement Stylus: AT-VMN95EStylus Size: 0.3 x 0.7 milType: VM Stereo Dual MagnetWeight  (Cartridge & Headshell): 15.5 g (0.55 oz)Wire Used for Coil: T.P. Copper