Cables to Go - C2G 33172 OM1 Fiber Optic Cable - LC-LC 62.5/125 Duplex Multimode PVC Fiber Cable, Orange (3.3 Feet, 1 Meter)

The Sanoxy 10m LC/LC Duplex 62.5/125 Multimode OM1 Fiber Optic Cable is a 10 m multimode fiber optic patch cable built for high-bandwidth, low-latency links between switches, servers, media converters, and patch panels. It uses OM1-grade fiber with a 62.5/125 micron core and cladding construction, which helps keep signal loss low across the run and supports the data rates commonly used in structured cabling and data-center environments. The ceramic-ferrule connectors are precision polished and protected by dust caps, while the duplex zipcord jacket stays flexible enough to route through trays, conduit, and rack channels without stressing the fiber. It is compatible with standard fiber transceivers, SFP and SFP+ modules, media converters, fiber patch panels, fiber network cards, and switch uplink ports that use the same connector type and fiber grade. Because fiber carries an optical rather than electrical signal, it suits long runs, building-to-building links, and installations where electrical isolation and interference immunity matter. Please review your device's port type and required length before ordering to confirm the correct fit for your setup.

Need a single mode jumper for a 10G SFP+ LR port where space behind the port is tight? This Cable Leader OS2 LC to LC fiber patch cable, also sold as a single mode fiber optic cable or LC duplex patch cord, uses Corning 9/125 G657A1 bend-insensitive glass in a 2.0 mm LSZH/OFNR riser-rated zipcord with short-boot LC/UPC connectors, insertion loss 0.30 dB or less, return loss 55 dB or better. OS2 fiber carries 1000BASE-LX and 10GBASE-LR links up to 10 km under IEEE 802.3, and the 19.5 mm short boot needs less clearance than a standard LC boot, so 48 ports on a 1U switch stay serviceable. Compatible with 10GBASE-LR and 1000BASE-LX LC single mode transceivers from Cisco, Ubiquiti UniFi, MikroTik, TP-Link, Netgear, Dell, HPE Aruba and Intel X520 network cards, and LC duplex patch panels. Each cable is sample-tested during production, and Cable Leader handles replacement requests directly. Best for: 10G LR uplinks between floors or buildings, dense 1U switch faceplates, LC patch panel jumpers. Not for: SR or SX multimode optics on aqua OM3 or OM4 fiber, green APC ports, or Toslink audio.

Need to link a 10G SFP+ switch port, server NIC or patch panel over multimode fiber? This Cable Leader OM3 LC to LC fiber patch cable, also sold as an OM3 duplex fiber optic cable or multimode patch cord, uses Corning 50/125 OM3 glass with a 2.0 mm zipcord OFNR riser-rated jacket and LC/UPC connectors on both ends, with insertion loss of 0.30 dB or less and return loss of 35 dB or better per connector. OM3 fiber is specified by TIA-492AAAC at 2000 MHz-km effective modal bandwidth, which carries 10GBASE-SR up to 300 m and 25GBASE-SR up to 70 m under IEEE 802.3. Compatible with 10GBASE-SR and 1000BASE-SX LC transceivers from Cisco, Ubiquiti UniFi, MikroTik, TP-Link, Netgear, Dell, HPE Aruba and Intel X520 or X710 network cards, plus LC duplex patch panels and couplers. Each cable is sample-tested during production, and Cable Leader handles replacement requests directly. Best for: 10G SFP+ uplinks inside a rack or room, server to switch links, LC patch panel jumpers. Not for: single-mode LR or LX transceivers that need yellow OS2 fiber, QSFP MPO parallel ports, or Toslink audio.