Customer Ratings & Reviews

So happy I made the decision to hardwire my camera to my Dodge Challenger! I feel much more at ease now that the camera is working around the clock keeping watch over my car. If you own this camera then this is a "no brainer"! Order this kit so you too can have peace of mind!

I have had a dash cam permanently installed in my Grand Marquis & I just had the Kenwood permanently installed in my Subaru. If you are getting a dash cam that is the only way to go. If you forget to plug in your dash cam & you have an accident then you wasted your money, & if you plug the dash cam in & forget to unplug the little thing then you will end up w/a dead battery. Like I say I am VERY happy w/the installation & it is well worth the investmentment.

This is a really gteat invvestment to ensure your car records (and it does 30 seconds before and after whenever touched - and I mean just a touch - or ANY gsensor detection) those bumps or wrecks that DO happen. It has saved my bacon and answered questions that no one could answer until the video evidence was seen. It is a must to have parking mode enabled on the kenwood a301 and a601 in car cameras.

A great product to hard wire your video cam into you cars wiring instead of having to constantly plug and unplug from cigarette lighter. Only problem item should of been included with the video camera instead of having to purchase separately.

This kit installation is easy and you are able to hide the wires better making for a clean look. This kit allows your dashcam to record events when your vehicle is off.

I've had my Kenwood dash cam for almost a year and finally decided to make the installation more "finished" looking. This kit makes it really easy. There is no wire cutting, attaching wire connectors, or soldering involved. You attach the black ground wire to a grounded location under your dash, you plug the fuse end of the "fuse tap" cable into the fuse panel and the "bullet connector" end of that same cable into the USB power cable. Tuck all the cables away and you're done. I've tinkered with car electronics before, but this product can be installed by anybody.

15 minutes to install myself. No need to use the cigarette lighter charger and run unnecessary wires across the dash.

Easy installation but adapters didn’t fit fuses for 2019 Nissan Rogue. Had to buy an additional 20 amp fuse.

Very useful for hardwiring and simple to install for my car. All supplies included

I ordered & installed two of these hardwired kits on two of my vehicles. They where simple and straight forward to install, took me longer to hide the cable behind the trim as i was cery careful not to break or crank thectrim. Works as intended

A fine kit that I never actually saw. It's there though, inside my dash. It's more than just a wire, it's an umbilical cord transferring life to our new dash camera.

It got me what I need a hardwire it works relatively easy to jnstall

Worked great, installation was a breeze, and took no time

Everything you need for a clean and factory look install

This is a great item to get rid of exposed wires. Youtube video helps for install.

Works like it should and easy to install. Cuts off if battery gets too low.

Worked aa intended , would recommend ….also was a great sale!

Bought with Kenwood dash camera. Works great. Had best buy install. Clean look

Used it to connect interior LED to AUX power without permanent modification to the car. Works reliable and super easy hidden install.

This is probably the worst accessory designed. Most dash camera hardwire kits want you to tap into an always hot circuit and a ignition switched source. This however is only looking for the always on, which will just make the camera always on and will drain your battery (it even stats in the manual if your not going to drive your vehicle for more than 2 days to unplug the dashcam.) It also has a straight plug instead of the right angle plug the original cord comes with which is a minor nuisanse. But my biggest gripe is that I went through the trouble of installing it and having the wires hidden only for it not to work at all. 12 volts goes in, but nothing is coming out, how does that slip past any sort of quality control, if there is any I suppose. So if you want a dashcam to be hardwired, buy a different dashcam.