StarTech.com - 1m Fiber Optic Cable - Multimode Duplex 62.5/125 LSZH Fiber Jumper Cord - LC/ST

Need to link a 10G SFP+ switch port, server NIC or patch panel over multimode fiber? This Cable Leader OM4 LC to LC fiber patch cable, also sold as an OM4 duplex fiber optic cable or multimode patch cord, uses Corning 50/125 OM4 glass with a 2.0 mm zipcord OFNR riser-rated jacket and LC/UPC connectors on both ends, with insertion loss of 0.30 dB or less and return loss of 35 dB or better per connector. OM4 fiber is specified by TIA-492AAAD at 4700 MHz-km effective modal bandwidth, which carries 10GBASE-SR up to 400 m and 25GBASE-SR up to 100 m under IEEE 802.3. Compatible with 10GBASE-SR and 1000BASE-SX LC multimode transceivers from Cisco, Ubiquiti UniFi, MikroTik, TP-Link, Netgear, Dell, HPE Aruba and Intel X520 or X710 network cards, plus LC duplex patch panels and couplers. Each cable is sample-tested during production, and Cable Leader handles replacement requests directly. Best for: 10G SFP+ uplinks, server to top-of-rack switch links, LC patch panel jumpers. Not for: single-mode LR or LX transceivers that need yellow OS2 fiber, QSFP MPO parallel ports, or Toslink audio.

Need to link a 10G SFP+ switch port, server NIC or patch panel over multimode fiber? This Cable Leader OM4 LC to LC fiber patch cable, also sold as an OM4 duplex fiber optic cable or multimode patch cord, uses Corning 50/125 OM4 glass with a 2.0 mm zipcord OFNR riser-rated jacket and LC/UPC connectors on both ends, with insertion loss of 0.30 dB or less and return loss of 35 dB or better per connector. OM4 fiber is specified by TIA-492AAAD at 4700 MHz-km effective modal bandwidth, which carries 10GBASE-SR up to 400 m and 25GBASE-SR up to 100 m under IEEE 802.3. Compatible with 10GBASE-SR and 1000BASE-SX LC multimode transceivers from Cisco, Ubiquiti UniFi, MikroTik, TP-Link, Netgear, Dell, HPE Aruba and Intel X520 or X710 network cards, plus LC duplex patch panels and couplers. Each cable is sample-tested during production, and Cable Leader handles replacement requests directly. Best for: 10G SFP+ uplinks, server to top-of-rack switch links, LC patch panel jumpers. Not for: single-mode LR or LX transceivers that need yellow OS2 fiber, QSFP MPO parallel ports, or Toslink audio.

The Sanoxy 15m OM4 LC to LC Duplex 50/125 Multimode Fiber Patch Cable is a 15 m multimode fiber optic patch cable built for high-bandwidth, low-latency links between switches, servers, media converters, and patch panels. It uses OM4-grade fiber with a 50/125 micron core and cladding construction, which helps keep signal loss low across the run and supports the data rates commonly used in structured cabling and data-center environments. The ceramic-ferrule connectors are precision polished and protected by dust caps, while the duplex zipcord jacket stays flexible enough to route through trays, conduit, and rack channels without stressing the fiber. It is compatible with standard fiber transceivers, SFP and SFP+ modules, media converters, fiber patch panels, fiber network cards, and switch uplink ports that use the same connector type and fiber grade. Because fiber carries an optical rather than electrical signal, it suits long runs, building-to-building links, and installations where electrical isolation and interference immunity matter. Please review your device's port type and required length before ordering to confirm the correct fit for your setup.