A:AnswerThank you for your inquiry about our Maytag appliances. For model MDB4949SKZ:
Was the dishwasher newly installed?
If you are receiving the F8E4 error code and the dishwasher was recently installed, check the following: https://youtu.be/OlND4BsYYaM
Do you see water?
Is the water supply connected correctly?
Check all the connection points. Be sure the rubber washer is properly seated in the fitting for any connection point. Slide the 3/4" (19 mm) fitting of the 90° elbow up to the valve and hand-tighten it to avoid cross-threading. Hand-tighten until the coupling is tight. Using pliers, check the tightness of the coupling. An additional 1/4 to 1/2 turn may be required to seal the rubber gasket. Make sure to route the fill hose out the rear left side of the unit. https://youtu.be/FP0981p6Fl8
Is the float switch connected?
Ensure the float switch is properly connected. Also, ensure that the power supply wire or cord does not touch the dishwasher motor or the lower part of the dishwasher tub. Reconnect the float switch by aligning the connector with the connector housing and pushing in until the locking tab is visible over the back of the connector.
Does the drip tray need to be emptied?
If you see water in the drip tray, it must be emptied.
To remove the drip pan assembly, press the snap at each side of the plastic tray in toward the center of the product and pull toward yourself. Take caution not to pull too far or too hard as the float switch wire is still connected at this time and pulling too far or hard can damage the wire. https://youtu.be/t5_g-zSnw9Q
Remove the Code
To remove the code:
Press the Cancel key once to silence the alarm tone.
Press the Cancel key again to clear the code.
Are there excessive suds?
Dishwashing detergent does not create suds, but dish soap does. If suds, bubbles, or soap foam are present when you open your dishwasher, turn off the dishwasher and allow suds to dissipate. Using the wrong type or too much detergent can cause over-sudsing. The suds may push water out of the dishwasher, causing leaking or poor wash performance. Use only detergent specifically designed for automatic dishwashers.
Dishwashers should be cleaned approximately every 30 days for optimal performance. Using affresh® Dishwasher Cleaner every month will help keep your dishwasher from filming and spotting and keep the interior clean and free of odors. https://youtu.be/yL_3IevWR-8
Dishwasher was Professionally Installed - F8E4 Error Code
The drain sequence will begin, and machine operation will be prevented
Turn off the water supply to the unit.
Press the Cancel key once to silence the alarm tone. DO NOT turn off the power and keep the door closed.
https://youtu.be/SXWqygseEqw
A:AnswerNo that's not a problem that's what mine does. I also use the quick cycle.
FYI make sure you run the hot water in the kitchen sink before starting the wash cycle. You get a better clean because of the water temp...
A:AnswerHello! Yes, the height without the feet on for model MDB4949SKZ would be 33 3/4". If needed, you may view the link to the Dimension Guide for this model. https://tinyurl.com/mpzvde4c Thank you for your inquiry about our Maytag appliances.
A:AnswerHello, we are sorry to hear you are needing parts. You may visit www.maytagreplacementparts.com to find and purchase parts online, chat with a parts specialist, or you may also call (844)200-5440 7 AM - Midnight - 7 days a week, to speak with a part specialist by phone. Thank you for your inquiry on our Maytag appliances.
A:AnswerHello, yes, this model comes in Black. It would be model MDB4949SKB. Please see the link to view this model directly. https://tinyurl.com/yc4d3rvw Thank you for your inquiry on our Maytag appliances.
A:AnswerHello, for model MDB4949SKZ, Maytag® Dishwasher, it can be plugged in or hardwired. The Power Cord it not provided with the Dishwasher. Thank you for your inquiry on our Maytag appliances.
A:AnswerHello, Yes, this model Dishwasher is available in white (MDB4949SKW). https://tinyurl.com/sx6v9umm Thank you for your inquiry on our Maytag® appliances.
A:AnswerHello! We are sorry to hear about your concern. We would recommend contacting Maytag® at 800-344-1274. We are available We are available M - F 8 am to 6 pm est They will be better able to assist you.
A:AnswerHello ScottB! The dishwasher will use a heating element. While the actual water heater is responsible for heating water before it enters the dishwasher, the heating element is a supplemental tool that serves several different purposes. Most modern-day dishwashers operate at a temperature between 130 to 170 degrees Fahrenheit. Water entering the dishwasher has an average temperature of 120 degrees Fahrenheit, which may or may not properly sanitize the dishes. The heating element, however, warms the water up by an additional 10-15 degrees; thus, effectively killing harmful bacteria and germs. In addition to killing bacteria, the dishwasher’s heating element serves a second purpose: to encourage faster and more efficient drying times.
