Questions & Answers

Q: QuestionWe’ve had this microwave for one year. The exhaust fan blows from the top when on but doesn’t draw the steam from the stove when cooking. No air flow from the bottom at all.

Asked 3 years ago by Jeff.

• A:Answer Hello. We're sorry to hear that your unit has not been operating as expected. The inconvenience is understood, and we recommend scheduling service with a certified GE Appliances technician that will be able to accurately diagnose and repair your appliance. You can do so by calling GE Appliance Service at 1-800-GECares (1-800-432-2737). We are confident that one of our techs will be able to help, and should you have any additional questions, please reach out to us!- Kianna@GEA

  Answered 3 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionI need to replace microwave. model jvm1870sfo2 What cu is this model and what would be a good replacement..

Asked 3 years ago by mickey.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Stainless Steel

• A:Answer Hey there, We're so happy to hear you're looking to replace your microwave and are considering GE! It'll be our pleasure to assist! The cu. ft. of this model is 1.8. If you would like a model in similar size, we'd recommend model JNM3184RPSS. Please note however, that you will need to use the mounting kit that comes with the model. This is because the kit is made specifically for that model. Thank you for your consideration. Mike@GEA

  Answered 3 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionMicrowave jvm6175skss. Reset filter button lite up red? It was installed 5 months ago. What does this mean?

Asked 3 years ago by Anonymous.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Stainless Steel

• A:Answer Hello. Thanks for reaching out! The light will illuminate after approximately 6 months of use to alert you to replace the charcoal filter (if used) and to clean/replace the grease filters. You can reset by pushing and holding the button for 3 seconds. We hope this helps, and should you have any additional questions, please reach out to us!- Kianna@GEA

  Answered 3 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWhat is a good replacement for GE Microwave Model #JNM1731DP1BB with same dimension since it was built in between cabinets and above the counter top stove?

Asked 3 years ago by tmac.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave - Black Stainless Steel

• A:Answer Hello. Thanks for reaching out! All 30" over-the-range microwaves are approximately the same width, and are designed to fit into a 30" wide cabinet opening. Therefore, the microwave you are looking at will work as a replacement for an existing 30" over-the-range model. When replacing an over-the-range microwave, the mounting bracket included with the new microwave should be used since the mounting bracket is specific to each model. The new screws, bolts, and exhaust adapter should also be used. We hope this helps, and should you have any additional questions, please reach out to us!- Kianna@GEA

  Answered 3 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionDoes GE microwave oven JVM7195DKBB uses same wall mount bracket and have same screw patterns as JNM1951DRBB model it replaces in the line?

Asked 3 years ago by microwaveanswers.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Slate

• A:Answer Don’t know with my old microwave I had to change the wall bracket.

  Answered 3 years ago by BpzoVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionHi I am replacing my GE Model JVM1339WW02 and would like to if there are any other white microwaves that I could use in its place for under the cabinet mounting with top rear exhaust. ModelJVM6175DKWW was an option but the wait time is 3-4 weeks.

Asked 3 years ago by Dave.

• A:Answer Hi - Thank you for reaching out to us and for your interest in a new GE microwaves. The great news is all of our over-the-range models would be suitable replacements. Here's a list of some of the models you might consider: JVM3160DFWW, JVM6172DKWW, JVM7195DKWW, or JVM3162DJWW. We're confident you will find a model to suit your needs. Kind regards - Vikki@GEA

  Answered 3 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionAfter many years my GE Spacemaker XL1800 microwave has broken and I would like to replace it with another GE over the counter range that has the same dimensions and quality . Any suggestions will be very welcome.

Asked 3 years ago by Ray.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Slate

• A:Answer Hello. Thanks for taking the time to reach out – we truly appreciate your loyalty as a GE consumer and are glad you were able to use your Spacemaker for many years! While we regret that your microwave has now broken, we have multiple replacement options. Unfortunately, without the specific model number of your Spacemaker XL1800, we cannot determine the exact dimensions (several different model numbers were produced in the Spacemaker XL1800 series). If you can reach out to us, here or over social media, with the model number, we would be glad to review further. You can also check our GE website for our various microwave options, if you wish; dimensions will be listed on the product’s page. We have over-the-range options (which can also be installed under a cabinet without a cooking surface below, though you would need to make sure the height clearances in the Installation Instructions are still met) as well as countertop options. We hope to hear from you soon, and are also glad to assist with any other concerns or questions you may have. All the best! -Sarah@GEA

  Answered 3 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionHow do I change the filter. Red light on. Where is the filter. Is there a video or pictures to show me. Where can I get one, and cost please

Asked 4 years ago by Feggy.

• A:Answer Hi there, and thanks for reaching out! The Reset Filter light illuminates when either the charcoal filter or grease filters need to be replaced or cleaned. (Once the filters have been replaced or cleaned, the alert can be reset by pushing and holding for 3 seconds.) If the vent filters are the issue, those can be cleaned and used again. We have care and cleaning details on page 20 of the manual (which can be viewed on our GE website by looking up the model number and going to the product page). The vent fan uses two metal reusable filters, which are on the bottom of the microwave. They can be removed by sliding them to the rear using the tabs, then pulling down and out. We recommend cleaning by soaking them, then swishing them through a hot water and detergent mix. If it’s the charcoal filter that needs to be replaced, details on that are on page 21 of the manual. This filter cannot be cleaned and would need to be replaced. The charcoal filter can be removed by first unplugging the microwave (for safety reasons), removing the vent grille mounting screws, tipping the grille forward and lifting it out, and removing the filter. There is a picture in the manual as well, if that might help. The charcoal filter is available under Part # WB02X35637 and can be ordered through our GE Parts website. While the cost can vary, the current cost through our parts website is $21.10. We hope this information is helpful! If you have any other inquiries or concerns, we are glad to assist any time. All the best! -Sarah@GEA

  Answered 4 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionCan I mount this in a cabinet and not above a range? What dimensions does the hole need to be? Do I need to do anything special?

Asked 4 years ago by Zwomann.

• A:Answer Hello- We appreciate you checking with us and are happy to help! Over the range microwaves can not be install in a cabinet or on a countertop. According to Underwriters Laboratories (UL), which approves appliance installations, you cannot use an over-the-range microwave on the counter or in a shelf. Besides not being approved for this installation, these microwaves don't have feet and are also often slanted (not level) on the bottom. Additionally, if the surface lights or vent fan were to be turned on accidentally, it could cause damage to the shelf or microwave. We hope this helps! If you have any additional questions, please let us know. We are here to help! Joyce@GEA

  Answered 4 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionDoes this have a feature of one push of a express timer number to set it off??

Asked 4 years ago by Susie.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Stainless Steel

• A:Answer The express number turns on with a push of the number and be canceled by pushing the cancel/off button.

  Answered 4 years ago by AnonymousVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: Questioncan I replace my model # JMV1650BB033 with model # JVM6175SKSS?

Asked 4 years ago by Anonymous.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Stainless Steel

• A:Answer yes but watch the door swing...may hit cabinet on left

  Answered 4 years ago by Greatzippylaptop

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: Questionmy PNM1871SM1SS went dead what is a good model that will fit with same bracket? will Model #JVM3160RFSS work?

Asked 4 years ago by tony.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Stainless Steel

• A:Answer Hi there, thank you so much for reaching out to us. Model JVM3160RFSS will fit your space, but you'll need to use the mounting bracket that comes with it. All 30" over-the-range microwaves are approximately the same width and are designed to fit into a 30" wide cabinet opening. Therefore, any of our 30" over-the-range models will work as a replacement for an existing 30" over-the-range model. We just suggest using the mounting bracket of your new microwave as these are model specific. We hope this helps clear things up for you and we're wishing you the absolute best. We'd love to keep you in our GEA family. - Guy@GEA

  Answered 4 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWhat are the total dimensions of the microwave

Asked 4 years ago by Sunshine.

• A:Answer 16 1/2" H x 15" D x 29 7/8" W

  Answered 4 years ago by 1966ChevelleSSVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: Questioncan i see a instalation manual, showing the location of the vent on top of the microwave? my old ge is vented outside and i have to know if the location on the new one would be the same.

Asked 4 years ago by bill.

• A:Answer Attaching pictures from manual

  Answered 4 years ago by PankajVerified Purchase

  • 
  • 
  • 
  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionI need to replace my GE JVM1870SF02, what other GE options do I have that will fit that you have in stock right now? Is this model one of them and/or are there others you can recommend?

Asked 4 years ago by jmt.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Stainless Steel

• A:Answer Hello there - Thanks for reaching out, we're happy to help! We believe this model will make a great replacement. All 30" over-the-range microwaves are approximately the same width, and are designed to fit into a 30" wide cabinet opening. Therefore, any of our 30" over-the-range models will work as a replacement for an existing 30" over-the-range model. We suggest checking availability with your local Best Buy. Thanks again! -Mikayla@GEA

  Answered 4 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWhat are the dimensions

Asked 4 years ago by Bud.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Stainless Steel

• A:Answer Hello - Thanks so much for reaching out! This microwave's dimensions are 16 5/16 H x 29 7/8 W x 15 9/16 D. All the best. -Mikayla@GEA

  Answered 4 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionMy existing GEProfile Spacemaker XL 1800 range microwave 2004 Model JVM1870SF02 stopped heating food etc. Can it be repaired.? which model will replace with the same size. Use of existing brackets?

Asked 4 years ago by Nanu1964.

This question was asked about the related product: GE - 1.7 Cu. Ft. Over-the-Range Microwave with Sensor Cooking and Defrost - Stainless Steel

• A:Answer Thank you for checking. Our appliances can be repaired and an authorized service technician can provide you what is needed to make the repair or if would be more cost effective to replace. Hope this helps. The new model will be JVM6175SKSS, JVM9179SKSS or JVM6172SKSS. You will need to use the new mounting bracket for the new model microwave but will fit in the same space. Hope this helps Geoff@GEA

  Answered 4 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWe need to replace a GE Spacemaker II Model JEM31WA 002 and we are looking for something compatible that will fit into the same space. I called GE and the unit they recommended does not look like the same dimensions . What microwave is compatible?

Asked 4 years ago by LG.

• A:Answer Glad to asked us the question as the model that was suggested will not work. Please look at the following model PEM31DFWW. If you have your present model on the countertop then you will have no issues. If you have your current model hanging under a cabinet then this will work. Should you have your present model built into a cabinet using an optional built-in trim kit then you will need a new trim kit in addition to the microwave as the old trim kit is not compatible with new model. Hope this helps. Geoff@GEA

  Answered 4 years ago by GE Answers

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWhat are the available wattage

Asked 4 years ago by Wineceller.

• A:Answer 1000W Microwave

  Answered 4 years ago by 1966ChevelleSSVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)