Questions & Answers

Q: QuestionWhat is the total quantity of banana plugs in the pack?

• A:Answer There are four banana plugs included in this pack.

Q: QuestionDo these speaker connectors fit standard banana jacks?

• A:Answer Yes, these speaker connectors fit standard banana jacks.

Q: QuestionAre these speaker connectors compatible with most speaker binding posts?

• A:Answer Yes, these speaker connectors have compatibility with most standard speaker binding posts.

Q: QuestionWhat type of plating is used on these speaker connectors?

• A:Answer These speaker connectors feature a direct silver-plated design.

Q: QuestionCan these banana plugs connect left and right speakers?

• A:Answer Yes, these banana plugs can connect left and right speakers to an amplifier or receiver.

Q: QuestionIs there a warranty included with the speaker connectors?

• A:Answer Yes, there is a limited lifetime warranty for parts included with the speaker connectors.

Q: QuestionI'm using 14 gauge-4 conductor speaker wire to have a single wire run to the two rear speakers from the receiver. Will there be a secure connection to these banana plugs for each individual conductor?

Asked 8 years ago by Chris.

• A:Answer Hello, yes these banana plugs will work perfectly for that speaker wire. The banana plugs use a series of set screws to tighten down onto the speaker wire. Just tighten the screws onto the cable to make a secure connection and you'll be good.

  Answered 8 years ago by AudioQuest Customer Service

  
  Helpful (4)Unhelpful (0)ReportAnswer this questionShow more answers (5)

Q: QuestionWhy can't I find these on AudioQuest's website? And why do they look cheap? It gives the impression that they're counterfeit.

Asked 4 years ago by FussySisyphus.

• A:Answer These work quite well, actually. the design of these "connectors" allows for significant contact between the wire itself and the connector surface via the "screws". I used them on 11 and 14 gage wire and am pleased with the results of the connectivity they offer. Plus, they save time in the assembly process. Can't address the "look", only the effectiveness of the intended purpose. Hope this helps.

  Answered 4 years ago by TeleddyVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionCan these be used to splice speaker wires?

Asked 2 years ago by Cemos.

Q: Questionwhat is the length of one of the plugs

Asked 3 years ago by PSVA.

Q: Question$54.95 for four connectors?

Asked 3 years ago by Ken.

Q: QuestionI have a set of bi-wire speaker cables that I need to put into a loudspeaker that isn't bi-wireable. The speaker ends of the cable are bare wire. Would these work as a sort of splitter to attach both bare wires to? If not, what might be the best solution?

Asked 3 years ago by AnalogJ.

• A:Answer If you have speaker wire with four strands you can braid them into pairs. Your bi-wire cable should have four colors of wire, at each end just pick two of the colors and braid the bare wire together, then do the same at the other end and repeat with the other two colors. Then take this connector and put it on the end of the braided wire and there you go you have two conductor speaker cable. Here is a video I found that talks about this, in fact, that is why I bought these connectors because I used them on this exact wire. https://youtu.be/XuqXoNAnXLU

  Answered 3 years ago by larryincmhVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (2)

Q: QuestionWill these work on spring terminals

Asked 4 years ago by Train.

• A:Answer You'll need Flex Pin banana plug for spring terminals.

  Answered 3 years ago by JT2700Verified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionShould one be able to unscrew the plastic jacket with finger pressure to expose the set screws to fasten conductor to banana plug?

Asked 4 years ago by Concerned.

• A:Answer Yes, you can. Make sure hand and/ or plug surface isn't slick from oil contaminants. Wipe off with micro fiber or paper towel dampened with isopropyl alcohol, then cover hand with rubber glove. You can also wrap both parts with rubber band and succeed. Typically, none of the aforementioned steps are necessary, other than clean and dry hands, because they're new and in box.

  Answered 3 years ago by JT2700Verified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)