how do you change the filter null

Detach the kuerig(k2.0) water tower and remove any water Twist and pull the inner shaft(clear) to detach At the base of that is the filter Remove the housing and replace filter Reminder: follow filter replacement instructions before Replacing cartridge, so you don't consume carbon deposits.

Inside the water tank you'll see a plastic insert that can be pulled out. You'll see at the bottom of the insert the filter is being held!

Pull out the canister going into your water resvoure and pinch the sides of the bottom to slide out holder. Slide new one into place (once you have followed the directions of soaking the new cartridge.) Then slide canister back into water resvoure until it clicks in then your done.

The exact procedure may vary from model to model, but it should be pretty close to the same on all I would imagine. You should be able to remove the water reservoir, just like you would when you fill it. Inside the reservoir, there should be tall plastic piece that you can pull on / out. At the bottom of that, you should find the old filter packet. Remove it, then insert the new pack after prepping it with the instructions included in the new filter box (I think it's something like soak the new filter for 5 minutes, then rinse thoroughly)

Hi Pastor. To change the filter, please remove the handle from your unit's water reservoir. On the bottom of the handle, press in the tabs on both sides of the base at the same time and pull down to separate. On the physical product, the tabs are located where the lines form an upside down triangle right above the Keurig word mark. Here’s a video to show you: http://krg.bz/1K25EJ3

If u have the filter stand? Just squeeze the bottom an it comes apart

The holder comes with directions on how to change. You basically just rinse and insert.

To remove the filter begin by removing the handle from your unit's water reservoir. On the bottom of the handle, press in the tabs on both sides of the base at the same time and pull down to separate.You can also refer to the video for a demonstration of changing the filter by going to the following address: http://krg.bz/1K25EJ3

remove the water intake tube where the filter hides under and snap out old and snap in the new

Lift the water container empty all the water and use long handle thong to remove filter

“how do you change the filter”

This question is for: Keurig - Water Filter Replacement Cartridges (2-Pack) - White

Asked by pastor 9 years ago

Answer This Question

See all questions & answers

Keurig - Water Filter Replacement Cartridges (2-Pack) - White-Front_Standard

1-10 of 10 Answers

Detach the kuerig(k2.0) water tower and remove any water Twist and pull the inner shaft(clear) to detach At the base of that is the filter Remove the housing and replace filter Reminder: follow filter replacement instructions before Replacing cartridge, so you don't consume carbon deposits.
Answered by BBelite 9 years ago
Sorry, there was a problem. Please try again later.
Inside the water tank you'll see a plastic insert that can be pulled out. You'll see at the bottom of the insert the filter is being held!
Answered by scotthx1138 9 years ago
Sorry, there was a problem. Please try again later.
Pull out the canister going into your water resvoure and pinch the sides of the bottom to slide out holder. Slide new one into place (once you have followed the directions of soaking the new cartridge.) Then slide canister back into water resvoure until it clicks in then your done.
Answered by Hinesty 9 years ago
Sorry, there was a problem. Please try again later.
The exact procedure may vary from model to model, but it should be pretty close to the same on all I would imagine. You should be able to remove the water reservoir, just like you would when you fill it. Inside the reservoir, there should be tall plastic piece that you can pull on / out. At the bottom of that, you should find the old filter packet. Remove it, then insert the new pack after prepping it with the instructions included in the new filter box (I think it's something like soak the new filter for 5 minutes, then rinse thoroughly)
Answered by Vinny 9 years ago
Sorry, there was a problem. Please try again later.
Hi Pastor. To change the filter, please remove the handle from your unit's water reservoir. On the bottom of the handle, press in the tabs on both sides of the base at the same time and pull down to separate. On the physical product, the tabs are located where the lines form an upside down triangle right above the Keurig word mark. Here’s a video to show you: http://krg.bz/1K25EJ3
Answered by Keurig Care 2 years ago
Sorry, there was a problem. Please try again later.
If u have the filter stand? Just squeeze the bottom an it comes apart
Answered by Gahart 9 years ago
Sorry, there was a problem. Please try again later.
The holder comes with directions on how to change. You basically just rinse and insert.
Answered by Fuzzbuster 9 years ago
Sorry, there was a problem. Please try again later.
To remove the filter begin by removing the handle from your unit's water reservoir. On the bottom of the handle, press in the tabs on both sides of the base at the same time and pull down to separate.You can also refer to the video for a demonstration of changing the filter by going to the following address: http://krg.bz/1K25EJ3
Answered by CommunityAnswer 9 years ago
Sorry, there was a problem. Please try again later.
remove the water intake tube where the filter hides under and snap out old and snap in the new
Answered by jacksam 9 years ago
Sorry, there was a problem. Please try again later.
Lift the water container empty all the water and use long handle thong to remove filter
Answered by jazzyGrandMa 9 years ago
Sorry, there was a problem. Please try again later.