Questions & Answers

Name: Frigidaire - 24" Front Control Built-In Plastic Tub Dishwasher with DishSense Sensor Technology, 54 dBA - Stainless Steel
Brand: Frigidaire
SKU: 10886087
Price: 399.12 USD
Availability: InStock
Rating: 4.4 (255 reviews)

Frigidaire - 24" Front Control Built-In Plastic Tub Dishwasher with DishSense Sensor Technology, 54 dBA - Stainless Steel

Model:: FDPC4314AS; |
SKU:: 10886087

User rating, 4.4 out of 5 stars with 255 reviews.

Highly rated by customers for:

$399.12

Save $50.87

Comp. Value: $449.99

Show only Answered Questions

Page Showing 21-26 of 26 questions

Ask a Question

QuestionThe “hold for 3 sec” options don’t work. Holding the dry button for 3 seconds doesn’t bring up the delay 4 hours light. Holding start button for 3 seconds doesn’t cancel the cycle. Is there something else I should be doing before I return this dishwasher?
Asked 2 years ago by NickyW.
- Answer I just installed it today. During the check for leaks, it instructed me to run it long enough to hear the water fill, then hold cancel for 3 seconds to pump out water. The instructions said the pump process takes 90 seconds. After I added dishes and ran a 1hr cycle to complete, I accidentally hit a button- I had to open the door and press and hold cancel for 3-4 seconds. Haven't messed with the delay 4 hours yet.
  Answered 1 year ago by ChristineInFlorida
  Answer this question
Questionis the filter drain in the back where its difficult to get to like most dishwashers?
Asked 1 year ago by ThatGuy.
- Answer Hi, ThatGuy! Thank you for this inquiry and for bringing this up. For this model unit, the filter is typically located at the bottom of the tub, which can make it somewhat challenging to access. However, many models are designed for easier cleaning, allowing you to remove the filter without needing to reach too far back. Please consult the owner's manual for steps on pages 14-15: Care & Cleaning': https://content.syndigo.com/asset/995a846b-6b75-41fe-97b2-d5eb846178a4/original.pdf ~Juan
  Answered 1 year ago by FrigidaireSupport
  Answer this question
QuestionCan this dishwasher be used as a free standing dishwasher? We do not have a counter to put it under.
Asked 1 year ago by Anu.
- Answer No this is for under a counter
  Answered 1 year ago by user860200
  Answer this question
QuestionI cannot get the water to run, only the motor runs when I start a cycle. It went through 1 full cycle last week with no issues, but now the water will not run on my 2nd use of it. It is BRAND NEW! do I need to Re-set it?? Please help!
Asked 2 years ago by Jennj.
- Answer Thank you for reaching out, Jennj. For some tips and recommendations for the best operation of this model, you can check out the user guide at the link provided. https://na2.electroluxmedia.com/Original/Electrolux/Electrolux%20Assets/Document/Complete%20Owners%20Guide/English/A23549801en.pdf If you need more assistance, just connect with us via phone at 800-374-4432, Monday-Friday, 8:30 a.m.–8:00 p.m. EST. ~Ruth
  Answered 2 years ago by FrigidaireSupport
  Answer this question
QuestionIs this dishwasher connected by plug in or hard wired?
Asked 2 years ago by krose.
- Answer Hard wired. Comes with the hardware to do so
  Answered 2 years ago by FrankL
  Answer this question
QuestionHow do you get the setting to change on wash cycle?
Asked 2 years ago by Child.
- Answer Hello! Thanks for reaching out to us! For Wash Cycle Selections: Cycle times are approximate and will vary with the options selected. Hot water is necessary to activate dishwasher detergent and melt fatty food soils. An automatic sensor will check the incoming water temperature and, if it is not hot enough, the cycle will be lengthened for automatic water heating in the main wash and final rinse of all cycles. This happens even when the high-temperature wash option has not been selected. When High temp wash is selected, an even higher temperature will be reached to handle heavier soil loads. Furthermore, the dishwasher is programmed to remember your last cycle so you do not have to reset each time. To start the dishwasher using the same cycle and options selected on the previous wash, just press the START/CANCEL pad. We hope this information is useful to you. ~Sam
  Answered 2 years ago by FrigidaireSupport
  Answer this question

Showing 21-26 of 26 questions

Questions & Answers

Frigidaire - 24" Front Control Built-In Plastic Tub Dishwasher with DishSense Sensor Technology, 54 dBA - Stainless Steel

Q: QuestionThe “hold for 3 sec” options don’t work. Holding the dry button for 3 seconds doesn’t bring up the delay 4 hours light. Holding start button for 3 seconds doesn’t cancel the cycle. Is there something else I should be doing before I return this dishwasher?

Q: Questionis the filter drain in the back where its difficult to get to like most dishwashers?

Q: QuestionCan this dishwasher be used as a free standing dishwasher? We do not have a counter to put it under.

Q: QuestionI cannot get the water to run, only the motor runs when I start a cycle. It went through 1 full cycle last week with no issues, but now the water will not run on my 2nd use of it. It is BRAND NEW! do I need to Re-set it?? Please help!

Q: QuestionIs this dishwasher connected by plug in or hard wired?

Q: QuestionHow do you get the setting to change on wash cycle?

Top Rated

QuestionThe “hold for 3 sec” options don’t work. Holding the dry button for 3 seconds doesn’t bring up the delay 4 hours light. Holding start button for 3 seconds doesn’t cancel the cycle. Is there something else I should be doing before I return this dishwasher?

Questionis the filter drain in the back where its difficult to get to like most dishwashers?

QuestionCan this dishwasher be used as a free standing dishwasher? We do not have a counter to put it under.

QuestionI cannot get the water to run, only the motor runs when I start a cycle. It went through 1 full cycle last week with no issues, but now the water will not run on my 2nd use of it. It is BRAND NEW! do I need to Re-set it?? Please help!

QuestionIs this dishwasher connected by plug in or hard wired?

QuestionHow do you get the setting to change on wash cycle?