Questions & Answers

Q: QuestionWhat is the frequency response of this line output converter?

• A:Answer This line output converter has a frequency response of 20Hz to 20kHz.

Q: QuestionHow is the PAC LocPRO line output converter powered?

• A:Answer The PAC LocPRO has a power input of 55W per channel.

Q: QuestionHow do you install the LocPRO line output converter?

• A:Answer It offers flexible installation with wire-tie or screw mounting options.

Q: QuestionCan I use this with my vehicle's factory audio system?

• A:Answer Yes, it is compatible with most vehicles. It has load resistors for OEM systems to enable wide-ranging use.

Q: QuestionWhat type of inputs does this 4-channel interface accept?

• A:Answer This 4-channel interface accepts both high-level and low-level inputs for integration with your existing audio system.

Q: QuestionI am having a kenwood dmx4707s put in my 2007 honda element ex. will I need this converter?

Asked 4 years ago by jae.

• A:Answer If your Element has the upgraded amplified 7-speaker system you would need this piece.

  Answered 4 years ago by AAMP Global

  
  Helpful (2)Unhelpful (0)ReportAnswer this question

Q: QuestionIm installing a new head unit with an internal amp, new speakers, and a subwoofer with an amp. i do not have a factory amp in my car. since im replacing my head unit, would i need this in my setup?

Asked 4 years ago by sal.

• A:Answer You would not need this line output converter when using an aftermarket radio. Your new radio will provide the RCA outputs needed for adding amplifiers. You would use this to add RCA connections a factory radio that did not have any.

  Answered 4 years ago by AAMP Global

  
  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionWill this work for a 2004 Lincoln Navigator? The vehicle has NAV & the THX system in it, will it work with these options as well?

Asked 1 month ago by Lincoln.

• A:Answer Yes. This is a universal line output converter that can be used in any vehicle.

  Answered 1 month ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionI’m having a Sony head unit installed why do I need this part added?

Asked 9 months ago by Bolen.

• A:Answer You don't, talk to your installation professional they'll help you schedule with all necessary parts.

  Answered 8 months ago by MatthewMVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionIt says 55w rated power but my aftermarket amp is 125w rms at 2 ohms and my front speakers are 90w rms and rear door are 100w rms would this still output the 125 to each of the 4 channels or would the loc be damaged since it is only rated at 55w.

Asked 11 months ago by Erick.

• A:Answer You will not use this after your amplifier. This will be used to change the radio speaker level output down to RCA level output for your amplifier input

  Answered 11 months ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionI have a 2020 Jeep Wrangler unlimited JL Sahara with a 7 inch display not the premium audio. Is this what I need to add to my system to add an aftermarket amplifier and subwoofer

Asked 1 year ago by Davo.

• A:Answer Yes, this line output converter will allow you to add an amplifier to your factory non amplified audio system.

  Answered 1 year ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWhy does this have ground, but no 12V? I think my connections are correct....But no sound. I know the amp had power, I don't know if the wires I used to connect the speaker wire to the amp were too thick or amp was too powerful or if I need a 12V wire

Asked 1 year ago by Mark.

• A:Answer This unit does not provide a remote turn on lead for an amplifier is it sued to take a speaker level audio signal and reduce it to an RCA level output for amplifiers that are not able to handle a speaker level input directly. Standard power, ground and remote turn on connections to the amplifier are still needed.

  Answered 1 year ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionCan I effectively use the 4 rca outputs going to two amplifiers, with only 2 speaker channels (RL & RR) connected to the wiring harness?

Asked 1 year ago by BigCee.

• A:Answer As long as all the input wires are connected to those two channels you are using for your input (white, gray, green, and purple pairs) yes.

  Answered 1 year ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionIs this what I’d need to install an amp to my factory 2019 Tundra radio?

Asked 1 year ago by Mitch.

• A:Answer Depending on which factory audio system the truck has this may work for you when adding an amplifier to the factory radio. Please visit a local store to go over any additional information needed to get you all the correct parts you will need for your installation.

  Answered 1 year ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionI have a 2001 Acura TL I just bought a pioneer head unit to be installed next month, does anyone know if I need this part because customer service is trying to add it on and I don’t know what it does or if I need it? Any help would be greatly appreciated.

Asked 2 years ago by Stef.

Q: QuestionMy 2010 Nissan Sentra does not have a factory amplifier but this is being added on to the aftermarket items I need to buy to complete the installation. Is this really necessary?

Asked 3 years ago by starguard.

• A:Answer This would be used to add RCA outputs to a system that does not already have them, for adding amplifiers. Most common uses are for adding amps to factory headunits, or aftermarket radios that have a limited number of RCA preouts.

  Answered 3 years ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionIf my deck only has 1 set of rca output but I want to install 2 amps would I use this? And how do I hook up 2 amps to this?

Asked 3 years ago by Ambybaby.

• A:Answer This line output converter could be used to add additional RCA outputs to a radio that doesn't ahve them or does not have enough for your needs.

  Answered 3 years ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionI am getting a Boss Audio 6.2 installed into my 06 Honda Odyssey. Do I need to purchase a LP6-4 (output converter) for the Multimedia Bluetooth to be compatible? I am not adding any new speakers just the new Bluetooth screen.

Asked 3 years ago by Chad.

• A:Answer The LP6-4 is used for adding amplifiers to a system that does not have RCA outputs. If your new radio has RCA outputs, or if you are not adding amplifiers, you would not need the LP6-2

  Answered 3 years ago by AAMP Global

  
  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: Questioni have a pioneer sx6000 1972 vintage will this converter work on this

Asked 4 years ago by Dls1971.

• A:Answer Absolutely is pretty straightforward it’s easy by the instructions to not give a call those guys are great to work with

  Answered 4 years ago by Bsummers82Verified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this question