The Velop Micro 6 Mesh router is a terrific option for anyone looking to conquer their home’s Wi-Fi dead spots and also don’t require “extras” like Ethernet ports on the child nodes, in addition to the parent node (router), or the very latest Wi-Fi standard, Wi-Fi 7. What I like most is that the Micro 6 is powerful without being a giant eyesore. It’s significantly smaller than most other mesh systems. It truly is micro-sized and can easily hide in plain sight.
MY SITUATION
My previous mesh Wi-Fi 5 router (802.11ac) + two child nodes dates back to 2017. Frankly it’s all I needed for my 4 level, 1800 sq ft townhouse until now. Recently though the number of smart devices/IoT I’ve added to my home has multiplied to the point this router couldn’t handle all the traffic. The result was devices started randomly disconnecting or would be slow to respond to commands. Speed-wise, I was still fine since I only have 300Mbps up and down broadband and I few Wi-Fi 6E devices and zero Wi-Fi 7.
So when I saw the affordable Velop Micro 6 Mesh router that included with two child nodes I thought I’d give it a try. The Micro 6 Mesh has what Linksys calls “Cognitive Mesh,” which, as I understand it helps better manage IoT devices, one of my big problems with my older router, just what I needed.
SIZE AND PORTS
This system is really shrunken down from the size of a typical mesh router, especially the child nodes compared to my older system. The main node is flat-ish, similar to a traditional MIMO router, but without the external antennas. It has a clean unassuming look. Don’t mistake that for lacking features though. It has four speedy 2.5 Gbps Ethernet ports and one WAN port. There’s also reset and power buttons.
The child nodes, on the other hand, are as basic as you get, just a single USB-C port for power. Perhaps because of its diminutive side, there is Ethernet port here. This may be a non-starter for those with, or planning to buy, IoT devices that depend on Ethernet or hub that requires Ethernet to work. An example here is the Philips Hue lighting system. With Ethernet only on the main node it limits placement of these kind of hubs and devices. Otherwise enjoy the child node’s diminutive size, similar to a 12oz soda can, that goes unnoticed on a shelf. You won’t miss not having Ethernet here.
SET UP PROCESS
Linksys also claims its Cognitive Mesh technology makes setup super easy. On paper that certainly looked to be true – plug in the router and nodes per instructions, install the Linksys app, snap a QR code on the user’s guide embedded with routers SSID and password, Select the router’s SSID on your device and follow the app’s instructions. The whole process at this point takes a couple of minutes to complete.
However, I did run into a few glitches, but overcame them after a quick troubleshooting. I won’t go into detail because I believe these were one-offs as I had no problems the 2nd try, and this doesn’t impact my opinion of this router. But I will say I’m not a fan of the set-up process or Linksys’s app. For one it assumes the user wants “WPA2/WPA3 Transitional” security. To be honest, I don’t know the formal SSID and password requirements for WPA3. What I do know is, based on the demands in the app, I’d have to update my Wi-Fi settings in all my smart devices as my current SSID and password were a character too short and had no symbols, just alpha-numeric. Only after I set up the router could I go back into the app and roll back security to WPA2 with my old SSID and password. I will eventually go WPA3 but this was not the day and I didn’t like being “forced” before I was ready.
PERFORMANCE
Once set-up I moved the location of the two child nodes around to find the optimal rooms to place each in. The main router must always be on the first floor because that’s where my Internet cable enters the house. I’ll add that my house is an open floor plan – only the bedrooms and bathrooms have doors. As a reminder, I have 300/300 Internet service.
I placed the two nodes in different floors and then do a speed check. “Rinse and Repeat” in different rooms until I was satisfied I tried enough combinations. My best result was a nodes in the halls on level 2 and 3. In this configuration my Internet speeds, with the bedroom doors open, were: level 1 300Mbps, level 2 300, level 3 250, level 4 175. For three of four levels that’s exactly or very close to my actual Internet service, something my previous mesh router never came close to getting. Even the 175 on level 4, while low, was better than I got with last router. Pretty impressive.
But it’s not all glory, there is a “but,” here. Inside the bedrooms, with doors closed, speeds dropped 25%. I will note that the interior doors in my house are standard builder’s grade and hollow, so YMMV if you have solid doors. Actually, since every house is different, it’s all a YMMV, but it looks like the Micro 6 Mesh has the power to fill in any dead zones your previous router could not. At least that is true in my situation.