A:AnswerThe APC BE600M1 is designed primarily for low-power electronics like routers, modems, and PCs. Most lift chairs draw significantly more power, especially during motor movement, which can easily exceed this UPS’s 330W capacity. While it might power the chair’s control system in standby mode, it’s not recommended for operating the lift mechanism during an outage.
For motorized furniture like a lift chair, you’ll want a higher-capacity UPS—ideally one rated for at least 1000VA or more, depending on the chair’s specs. But always check the chair’s power requirements and consult the manufacturer or APC support to ensure safe compatibility.
A:AnswerJassed, I have not ever tried it but if you use it solely for that purpose I could see this lasting for days. I use apc for my two aquariums (one in each) and have been pleased, it is much better/cheaper option then some of the aquarium specific options imo.
A:AnswerThe APC BE600M1 has a 330W battery capacity. If you're only powering a 65W Chromebook and an 18W DSL modem (totaling 83W), you can expect around 2.5 to 3 hours of runtime during a power outage. This assumes the battery is fully charged and the devices are drawing consistent power.
Keep in mind that actual runtime may vary slightly based on battery age and usage conditions, but this setup is well within the UPS’s capabilities for short-to-medium outages.
A:AnswerYes, the APC BE600M1 UPS will automatically restart once power is restored, even if the battery was fully depleted during the outage. As long as the incoming voltage is within the unit’s operating range, it switches back to online mode without requiring you to press the power button.
A:AnswerYes, the APC BE600M1 is an uninterruptible power supply (UPS)—it provides battery backup and surge protection for devices like routers, switches, and modems during power outages or voltage fluctuations.
As for plugging it into a surge protector: APC recommends plugging the UPS directly into a wall outlet, not into a surge protector or power strip. Connecting it through another surge device can interfere with proper grounding and may prevent the UPS from functioning correctly during an outage or surge event.
Since you're just plugging in a switch and router, this UPS is a great fit—it’s designed to keep networking gear powered for extended periods during outages.
A:AnswerA flashing red light and constant beeping on the APC BE600M1 usually means there’s a fault condition—most commonly a disconnected battery, overload, or battery failure. Here’s what you can try before returning it:
- Check the battery connection: Open the battery compartment and make sure the battery is securely connected. A loose or unconnected battery is a common cause of this issue.
- Reduce the load: Unplug all devices from the UPS and see if the beeping stops. Then plug in one low-power device (like a modem) and test again.
- Let it charge: Leave the unit plugged in (with the power button off) for at least 10–24 hours to allow the battery to fully charge.
- Reset the unit: Some users have had success by unplugging the UPS, removing the battery, pressing and holding the power button for 10 seconds, then reconnecting everything.
If the red light and beeping persist after these steps, the unit may be defective or the battery may be unusually depleted. You can find more troubleshooting tips in APC's official guide.
A:AnswerIf you're only using the APC BE600M1 for a modem/router, the battery can last around 51 minutes on average, assuming a power draw of about 50 watts. If your setup uses less power—say 20–30 watts—you could see up to 90 minutes or more of runtime. Actual results may vary depending on battery age, device load, and environmental conditions.
Personally I saw 2 hours with my network setup, but that time will drop as the battery ages.
A:Answer“Runtime” refers to the total amount of time the UPS can power your device during an outage—regardless of whether the device is actively in use or just in standby. So in the example you mentioned, the 51 minutes of runtime means the UPS kept the router powered for 51 minutes continuously, whether or not someone was making a phone call.
For your Xfinity Voice router, that runtime would cover both standby and active use, as long as the power draw stays consistent. Keep in mind that actual runtime can vary depending on the router’s power consumption and battery age.
I have a heavier load than most people, with two routers, a cable modem, and an 8-port switch. Even so, the APC BE600M1 UPS keeps my network running through outages lasting up to two hours for me. As the battery ages, that up time will drop.
