Universal Wireless Rear Speaker Kit

I'll start by saying that I read almost every review available for this unit before purchasing and what I decided is that I need to buy it for myself to really make my own conclusions. (remember that you can always return it if you don't like it) My system consists of the following.... (Fronts) Klipsch RP-280fa (Center) Klipsch RP-450ca (Rears) MartinLogan Motion 4's (Receiver) Marantz SR-6011 I have to admit that I wasn't expecting much from this wireless kit as it's only putting out 30 Watts into 4ohms which is nothing to get excited about but since this unit is meant for the rear speakers, it is acceptable in a small to medium sized room (mine is 16x13). After all the cabIes were hooked up, I made sure the wireless receiver and wireless sender were within viewing distance of each other and setting the volume on the rear wireless receiver at Max. Then I ran the Audyssey EQ calibration on my receiver and was surprised to see that it worked perfectly. You don't need to have a calibrator on your receiver for this unit to work as it is a plug and play system. Once the calibration was complete, I used Mad Max: Fury Road (dolby atmos) to demo the setup. I wish I could say it was amazing but my rears lacked the low end that can be provided by a more powerful amp but the highs were present and were allowed to shine. Now given the size of my room, I am not even using a subwoofer as my towers have dual 8" woofers so the bass is more than enough to make up for what I may be lacking in the rear. Some important things to note.... 1. Follow the directions exactly as they are explained in the instruction manual. 2. Understand that if you do not have a dual band wireless router then you may experience interruption and delays in either your speakers or your wireless speeds to your devices ie. smart phone, tablets, media players etc. I have all my devices connected to 5ghz and let this unit take over the 2.4ghz so that I am assured no issues. As long as you are not expecting audiophile performance, I can happily recommend this system to anyone that is looking to go wireless. I'll say it again.....you can read all the reviews there are but you won't really know until try it yourself.

I have wanted to add surround sound speakers in my den for a while but put it off due to the time and money it would have required. I saw this wireless speaker option and checked the reviews. They were positive so I decided to give it a try. VERY glad I did. The setup was quick and easy and all of the necessary wires are included. It is as simple as connecting the speaker jacks, on your receiver, to the transmitter. Then locating where you want the speakers to be. Connect your wires to the Amplifier/Receiver and plug it in the wall. Then just adjust the settings for volume on your receiver and the Rockfish amp. Total time for me to set up was about 30 minutes, which included mounting the receiver, speakers and running wire.

Great product, works perfectly with our new setup with no speaker wire running from the back of the room to the front where our receiver is located. Did not degrade the sound at all that the human ear can notice. I recommend this for anyone looking to convert wired speakers to a wireless setup.

Let me tell you about this system.. I wanted to be outside and still hear what's on the TV. I didn't want to run wires all through the frickin' house, I mean after all I'm a dude trying to listen to my TV outside, I'm lazy if you haven't picked that up yet.. But anyways, I plugged this into my Samsung Blu-Ray Surround Sound System (another great buy from Best Buy!!), but anyways I connect one device to the sound system and another one to my speakers I put outside. After syncing the devices I get sound outside from my TV rooms away! The distance is remarkable and I'm very happy. I get that what I'm using these for are not what it's made for, but my two cents is if you want your sound in multiple rooms, this is a very cost effective way to make that happen!

amazing product surround sound made easy i highly recommend this product

This product looked just right to solve my problem. I bought a great TV (Samsung 55" Series 8) and the matching Samsung HW-C700 A/V 3D receiver to match back in March. Along with a great picture, I am a musician and audiophile. I have a very good ear for music and the quality thereof. So after making my initial purchase which also included front towers, center channel, and subwoofer (all Polk Audio), I wanted to complete my surround sound by adding two rear speakers. I got a great deal on a couple Polk bookshelf speakers on a Black Friday sale, but I didn't want to run wires from my A/V to the back since I have vaulted ceilings and hiding the wires would be a lot of work for me. There's my situation and this product look like a great solution for me in my room. Setting up the wireless system (installing the wires [which I used monster 16gauge wire] and hiding them) took me about 30 minutes and calibrating it with my A/V receiver was really easy. I had previously worried a lot about the signal latency (15-20ms published, which is right on the money) which I had feared would create an echo. It may for you, if you don't have an A/V receiver that can automatically or manually set signal delay or sync for your individual speakers. I was about to get it all synced up and made the entire setup and calibration under 45 minutes. After listening for a while to various forms of media, I could hear something wasn't right to my ears. I listened to lots of high quality music and blu-ray high def audio and in these trials something just didn't sound right to me. My troubleshooting approach was to A and B the speakers with one connected directly to the A/V receiver and one connected to the wireless rocket fish. A few minutes of listening I could tell what the problem was and I later confirmed it in the specs. The Rocketfish Wireless Rear Speaker Kit's manual stats that it transmits and receives Stereo, 16-bit, 48Khz uncompressed audio with a bit-rate of 1.465 Mbps. The Signal to Noise Ratio is 87dBs and output power is 2 x 25W RMS (in 4 ohms). Okay? So, the transmitter has to down-sample my 96Khz PCM high-def audio that my A/V receiver is sending. That is one of the differences in quality. Another is the RMS, my receiver can give 120 Watts RMS per channel (at 6 ohms). Also, It's no wonder that there is a slight hiss produced due to the signal to noise ratio. It is most recognizable when the Rocketfish receiver's volume control is cranked. For me, the Rocketfish solves the problem of hiding wires across a room at a cost of quality and hiss (the hiss isn't terrible and may not be noticeable in your environment. It can also be controlled with some trail and error, but you'll sacrifice volume and headroom). Of course, I'm comparing this to my A/V receiver which is awesome in comparison and rightfully so! The differences make the quality of sound noticeable to me, but not my non-audiophile wife. So. Audiophiles beware, but if you aren't an audiophile that can pick out slight discrepancies in the signal, this product is really great. I am halfway tempted to keep it because I'm dreading the day's job (and money spent) of running the wires to the back of my home theater. But, for me, high quality audio is an ever elusive beast that I hope to one day capture.

My house shakes with 5.1 sound again. WatchING mission impossible rogue nation. Saweet!! To hear the special effects reverbate through my system is awesome, and now I have my two rear speakers on board. My room is 15 feet long, and the rear speakers are hidden in a hutch 8 feet tall. Direct line of sight from my pioneer 3d capable receiver makes setup a snap. The unit is pre programed from the factory, no setup is needed. I did experience some feed back but you can turn the volume up or down on the receiving unit...set it and forget it! The sound you get depends on your receiver, but that is not an issue. The units simply relay sound from the signal coming from the rear speaker setup at your receiver and relayed back to the receiving unit. Both units have a blue light that flashes blue we. You first turn them on then go to a steady blue light. This means they are connected. If not, there is a connect button on the receiving unit. Simply connect your speakers .. instructions included. ..turn on the sending unit, connect your speakers to the receiving unit and push the connect button. Couple seconds should do it. Enjoy.

Let me start by saying it works as advertised. It is easy to setup, install, and sounds great. We have it spanning 50 or so feet to power rear speaks in our kitchen leading to an open plan living room. What I don't like!!! I spent three days and then purchased a 2.4GHz spectrum analyzer to discover my WiFi interference was due to this speaker system. The trace shows a strong RF signal and when I switch off the transmitter it all goes quiet. Plus the speaker system shifts frequencies randomly, presumably to avoid interference, so don't be fooled into thinking your WiFi is fine after install. I noted two traces, presumably for left and right channels, at WiFi 4.5/12 and then it shifted to 6/14. Good luck :-)