Questions & Answers

Q: QuestionCan I stream music wirelessly to this receiver?

• A:Answer Yes, you can stream music wirelessly using Wi-Fi or Bluetooth, and it supports services like Pandora, Spotify, and TuneIn.

Q: QuestionIs this receiver compatible with Dolby Atmos?

• A:Answer Yes, the Denon AVR-X2800H supports Dolby Atmos surround sound for an immersive audio experience.

Q: QuestionHow many watts per channel does this receiver deliver?

• A:Answer This receiver delivers 95 watts per channel at 8 ohms.

Q: QuestionDoes this receiver support 8K video pass-through?

• A:Answer Yes, the Denon AVR-X2800H supports 8K/60Hz and 4K/120Hz video pass-through.

Q: QuestionWhat is the maximum number of channels supported by this receiver?

• A:Answer The Denon AVR-X2800H supports a maximum of 7.2 channels.

Q: QuestionThe specs say depth of 17.1 inches and width of 13.4 inches. Based on pictures, those must be backwards, yes?

Asked 2 years ago by Miked113.

• A:Answer If assuming depth to be from the face to back of the unit, then yes the depth is 13.4 inches.

  Answered 2 years ago by AnonymousVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (2)

Q: QuestionMy geek tech said I needed to buy at least 7.2 Denon What is 7.0 Denon? Are they interchangeable?

Asked 2 years ago by SueBee.

• A:Answer The 7 in 7.2 means the number of amplifiers on board provided for the main speakers. Up to seven speakers can be connected. The 2 in 7.2 is the number of subwoofer pre-outputs provided. Up to two subwoofers can be connected.

  Answered 2 years ago by Denon Team

  Helpful (3)Unhelpful (0)ReportAnswer this question

Q: QuestionCan Denon AVR2800H drive Jamo C95 floor standing speakers with a Jamo C912 subwoofer to its peek and without distortion.

Asked 2 years ago by Jamo.

• A:Answer You can drive any amp to distortion, including this one. This receiver will probably be a little weak legged for those speakers if the task is solely to drive those speakers.

  Answered 1 year ago by ClaytonPVerified Purchase

  Helpful (2)Unhelpful (0)ReportAnswer this question

Q: Questionwill this reciever handle/ push 4 ohm speakers safely with great sound, cerwin vega AT-15's

Asked 3 years ago by mike.

• A:Answer Hello, the Denon AVR-X2800H receiver is compatible with 4 - 16-ohm speakers. Cerwin Vega AT-15 speakers are relatively easy to drive as they have a sensitivity rating of 96dB. The AVR-X2800H will have no problem driving the speakers.

  Answered 3 years ago by Denon Team

  Helpful (2)Unhelpful (0)ReportAnswer this question

Q: QuestionIs the Denon AVR-X2800H a good replacement for the Denon AVR-2808CI? I have a 7.2 set up with Paradigm Milenia R,L,C speakers and Paradigm ADP surround and rear speakers

Asked 1 year ago by SnowbirdInAZ.

• A:Answer Hello CB, thank you for your inquiry. The modern equivalent of the AVR-2808CI would be the AVR-X4800H receiver. However, if you do not need the extra channels of amplification and inputs provided by the 4800, the AVR-X2800H would be a suitable replacement and pair nicely with your speakers.

  Answered 1 year ago by Denon Team

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionWill this drive two Martin Logan Motion Foundation F2s, two Martin Logan Motion Foundation B1s, and a Martin Logan C1 2.5-Way Center Channel Speaker as a surround sound set-up or do I need something with more wattage per channel?

Asked 1 year ago by Craig.

• A:Answer Hello. Yes - the AVR-X2800H will drive the Foundation F2s, 2 x Foundation B1s and a C1. if you have a larger room or/and you enjoy spirited volume levels, I suggest the AVR-X3800H. Not only does the AVR-X3800H have more power, but it also has a full bank of pre-outs - just in case you ever wanted to get more performance from the Martin Logans by adding optional external power amplification.

  Answered 1 year ago by Denon Team

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionCan I connect 3 ohm impedance speaker to AVR X2800H receiver. If no, there are any other solutions to connect

Asked 1 year ago by sam.

• A:Answer Hello. In some cases, yes. It does depend somewhat on which speaker make and model you have. Impedance is always an average measurement. Without knowing the speaker make and model, it isn't possible for us to be certain either way.

  Answered 1 year ago by Denon Team

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionI HAVE BOWERS AND WILKINS 700 SERIES TOWER SPEAKERS. WILL THE 2800 PRODUCE MAXIMUM SOUND QUALITY FROM THOSE SPEAKERS?

Asked 1 year ago by TGLT.

• A:Answer If you are looking for a Home Theater/Music system, the Denon AVR-X2800H is definitely up to the task. With the AVR-X2800H, you can configure the receiver to Bi-Amplification in the amp-assigned setup menu for additional power and control over your front speakers. https://manuals.denon.com/AVRX2800H/NA/EN/DRDZSYcqhsmjdu.php

  Answered 1 year ago by Denon Team

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionCan I use two remotes on the same unit?

Asked 2 years ago by Anonymous.

• A:Answer Hello, If you have two compatible remotes for the AVR-X2800H, they can both be used - so long as only one of them is firing a command at a time.

  Answered 2 years ago by Denon Team

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionDoes this unit have a built in equalizer. I’m currently using a 20 year old demon putting out 110 watts per Chanel, but it is only capable of 5.1 surround. Just not sure if $1600. Upgrade is worth the money. I recently purchased a Samsung 85” qled90.

Asked 2 years ago by Oldman910.

• A:Answer You can access an equalizer easily through the app and I think through the various menu options clicking through with the remote, and it has a separate basic tone control for bass and treble.

  Answered 2 years ago by EmceeNVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionWill this work with a record player as an amplifier?

Asked 2 years ago by Farin.

• A:Answer Hi Farin, Yes - you can connect a record player to the phono port on the rear panel of the AVR-X2800H.

  Answered 2 years ago by Denon Team

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionDoes this product work on 240 volts supply?

Asked 4 months ago by Rajeev.

• A:Answer Hello Rajeev. All of our AVRs - including the AVR-X2800H - sold in North America are designed to work on a 120V electrical system.

  Answered 4 months ago by Denon Team

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionDoes this AVR support an IR repeater so I can use the remote when the unit is enclosed in a cabinet?

Asked 4 months ago by Newbie.

• A:Answer Hello Newbie. Yes - the AVR-X2800H does support the use of an IR repeater. Here is a link which details how thisn is done when using a remote control receiver: https://manuals.denon.com/AVRX2800H/NA/EN/GFNFSYnhfzqtxu.php#WBSPMLbzfjlmvh

  Answered 4 months ago by Denon Team

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionHow does the sound compare to Marantz Cinema 60

Asked 6 months ago by Todd.

• A:Answer Hello Todd. That depends largely on which speakers are being used. If the speakers in question are not very demanding and reasonably sensitive (88dB or higher and in a small to medium sozed room), there may not be a significant difference to be heard between the AVR-X2800H and the Cinema 60. Cinema 60 is a little better equipped to drive a wider range of speaker types and loads.

  Answered 6 months ago by Denon Team

  Helpful (0)Unhelpful (0)ReportAnswer this question