Customer Ratings & Reviews

I built a metal shop and could not get WiFi into it. This device worked for me. My shop has a window so that probably helped but regular WiFi extenders would not work - this did!

Insane wifi distance. Mounted outside of my house to supply shop with wifi and even the 5ghz band gets full signal from inside shop. Easy setup. Buy the proper mounting pole size. It doesnt come with one.

WINEGARD - EXTREME 2.0 HIGH PERFORMANCE OUTDOOR WI-FI EXTENDER MODEL:RW-3035 GOOD WIFI EXTENDER AP FOR WIRED USE The WINEGARD - EXTREME 2.0 HIGH PERFORMANCE OUTDOOR WI-FI EXTENDER is very easy to use and to setup. There is not much to it really. The antenna is well protected, and it is nice that there is mounting gear included. It does a good job, when configured as a wired to Wi-Fi access point, but it is not so good as a WiFi-WiFi extender. I was able to get a “usable signal” at about 400 ft line of site. As long as you can physically connect the included POE (Power Over Ethernet) adapter to your wired network or a spare port on your router, then you should be satisfied with the performance. However, if you are hoping to boost a weak Wi-Fi signal and suddenly make it stronger this is not how things like this work. In Wi-Fi to Wi-Fi mode you are only as good as your weakest Wi-Fi link. If you get for example 100 Mbps just outside the wall of your house, with the overhead of WiFi to WiFi you might get up to 40-60 Mbps a 100 feet into your yard / outdoor space though likely closer to something like 20Mbps. However, if you are connected to a wired network, then you can probably get close to 90-100Mbps (assuming 100Mbps is your normal max speed). A lot of it depends upon what you need the Wi-Fi for. Email, fine. Video Calls, probably not. It is not magic. If you can barely get a signal outside your home, then unless you wire this to your home network you will not get any usable additional bandwidth. I do highly recommend that you enable the 5Ghz band, as I had far better performance (faster) than 2Ghz even at 400 ft from the WINEGARD - EXTREME 2.0 HIGH PERFORMANCE OUTDOOR WI-FI EXTENDER. SETUP: The setup is really easy and straight forward. Just plug it in. Wait for the Wi-Fi Name to come up, connect to it then configure it using the information printed on the instruction sheet. Every time you change anything on a setup page, you need to press “Continue” to save the settings, and then wait a few minutes for the router to incorporate the changes. It would have been nice if WINEGARD include a cable or two for initial setup and maybe even deployment. At least with their antennas they, usually include 25-100 feet of coax. SOME GEEKY STUFF – OK TO SKIP My baseline speed from my (2021) laptop to my in house Wi-Fi network (2019) is about 500Mbps to the internet. If you are attempting Wi-Fi to Wi-Fi extender mode (the default mode), you should know that the source Wi-Fi can only be on the 2Ghz Network. (I have confirmed this with WINEGARD support). Next you can’t have the source network be one 2Ghz channel (like 3) and the rebroadcasted channel to be something less crowded (like 2Ghz / Ch 9). So, this means 2 things. First, there seems to be only one 2Ghz radio that must be utilized to both transmit and receive on the same channel. Next this also means that the WINEGARD - EXTREME 2.0 HIGH PERFORMANCE OUTDOOR WI-FI EXTENDER is stomping on the source Wi-Fi and adding to the congestion by rebroadcasting on the same channel. In my testing, performance dropped by about 80% (to about 20 Mbps) when using only the 2Ghz network. Once I enable the 5Ghz network, I was able to slightly increase performance (around 55 Mbps). Once I changed to “wired to Wi-Fi” (ethernet) mode. I was getting about 80Mpbs on the 2Ghz band and 160Mbps on the 5Ghz band. Not great by any means, but usable for sure. (see pics) The documentation says the antenna is omni directional, which then made it no surprise then that the signal dropped off very quickly. Sure, I could still connect even at 400ft (clear line of site) from the WINEGARD - EXTREME 2.0 HIGH PERFORMANCE OUTDOOR WI-FI EXTENDER, but 2Ghz was about 20 Mbps and 5Ghz was about 80 Mbps. On one hand this is a good signal for the 5Ghz, but I was surprised by how much the 2Ghz dropped off. By way of comparison, I have another very inexpensive outdoor Wi-Fi antenna that is extremely narrow band uni-directional, but I was able to get a similar usable signal almost 3/4 mile away though I had to have the antenna lined up perfectly. For best performance on Wi-Fi only extenders (WiFi to WiFi), you really need 2 (or more) radios each dedicated to either connecting to the source to re-transmitting independently set to different channels. For this price point I was a little disappointed that the WINEGARD - EXTREME 2.0 HIGH PERFORMANCE OUTDOOR WI-FI EXTENDER does not seem have multiple TX/RX radio/antennas for each frequency. I’ve long forgotten the math, but if I recall there is something like a 4X negative impact on throughput using the same radio/antenna combination for rebroadcasting a signal. A CAUTIONARY NOTE ABOUT GENERAL SECURITY FOR ACCESS POINTS Make sure you configure all the passwords to strong passwords, change the default password on the WINEGARD - EXTREME 2.0 HIGH PERFORMANCE OUTDOOR WI-FI EXTENDER (or any AP/router). If for example, you set up the “guest network” with a password of “guest”, you can easily (accidentally) give everyone in your neighborhood or apartment access to everything on your home network. BE CAREFUL. This is an access point device, it is not a firewall nor does it contain any advanced security features. Because this is such a strong antenna, I was easily able to see about 10 other neighbor’s networks as well as dozens of devices like speakers and TVs. Many of these had no password protection. Remember if you can see your neighbor’s networks, then they can see your network as well. If you are an advanced user, then you should try to isolate all traffic to/from your AP to “internet only” to protect your internal devices. Most routers have some capability in this regard. SUMMARY / RECOMMENDATIONS So, boiling it all down. If you just want something super easy to deploy and are not obsessed over lightning fast performance, then the WINEGARD - EXTREME 2.0 HIGH PERFORMANCE OUTDOOR WI-FI EXTENDER will work just fine. My main advice is to wire it to your router if at all humanly possible for better performance. But if you are just chillin’ on your patio and want some signal this will work well enough. If you can’t wire it to your router at least enable the 5Ghz network and use that when possible for better performance. So I will give this a recommend, but only for wired use.

Winegard Extreme 2.0 Wi-Fi extender is a wireless-AC access point and extender designed for outdoor needs with simple setup and mounting options. My home is a single-story 4000+ SQ ft and have mesh wireless for indoor but when it comes to outdoor the wireless signal drops to one bar when browsing in backyard. Also, smart devices like Rachio, Flo by Moen, Ring outdoor cameras was suffering from signal issues until this outdoor Wi-Fi extender was professionally installed at my place. Setup was easily. Installation guide was a single piece of paper to assemble the extender with arms that was included in the box. Packing was not great. My unit came in brown box with no packing materials. Not sure if its retail unit but the unit was plastic wrapped and new. I had my AV guys install outdoor cameras and they installed CAT6 cable from my indoor where my router sits. Keep in mind, the cable cannot exceed more than 85 feet in length for it to work. So, I had to choose a place outdoor where its around 80 feet. It does come with power adapter where the cable for ethernet (if wired) and the CAT5E/CAT5/CAT6 cable is plugged in for POE. Cable is not included in the package. Suggest watching few YouTube videos from manufacturer for quick installation and setup. It explains well and speeds up the whole process like breeze. Set your password stronger as this will be mounted outdoor, and anyone can easily hack to your network, if need be, with poor password. Also, turn on the 5GHZ frequency band for greater speeds and make sure to setup guest account with different password to share with guests. To setup you need to enter 10.11.12.1 on your web browser and don’t forget to change the default admin password and check for software updates. Now I have stronger high performance Wi-Fi extender for outdoor and secure (supports WPA, WPA2 and WPA3). Overall, it’s an excellent outdoor Wi-Fi Extender, access point, bridge mode with great range and now all my smart devices that are installed outside gets consistent strong Wi-Fi signal and will recommend to anyone who needs outdoor strong signal strength.

Set up is really easy and straightforward. Plug it in, connect to it with your phone then add it to your home network. Took minutes to do. The only tricky part would be installation outside, depending on your outdoor layout. I need to decide if I want to bury an ethernet cable across my yard and mount on the post further away from the house or house mount and run off poe. If I do that though, I'll need to update my outdoor outlet enclosure to make sure I can keep the flap open in all weather. If you're dual band (which most people should be at this point) you'll want to set up the 5Ghz Using Google maps, it looks like I have a church just about 1000 feet from where it'd sit in my yard and a playground in the opposite direction. I play mobile games with my kids that require walking outdoors. It's handy to be able to go visit stops and whatnot without me needing to use a Hotspot on my phone since their tablets don't have their own data plan. Long term testing will be needed to see how it fares in all weather since we get snow and rain, but given how the seals look at connections, I don't have reason to think it'll leak and be damaged

I used to have an issue when I'm out working in my lawn or doing a movie night in the backyard. That was because I didn't have a good WiFi connection outside. Ineverreally thought much of it until I got this Winegard extreme outdoor WiFi extenter access point. I feel safe knowing that my WiFi this thing is secure. It has a little bit of a learning curve as far as set-up, but there is a Youtube video for the whole process that helps It has some serious reach. So well that I can actually connect my WiFi from the block behind me. As long as your password is secure, you're gonna all aces. The only thing I really have a problem with is there's no ethernet cable. And I had to get a 50 ft cord so i could properly place it outside, where I wanted it. Butonce it was done, it was done. Now I see backyard movies becoming a reality. I recommend this to people with large yards or lots of land. I think if I didn't like to jog in my nieborhood or stream music and movies in my backyard, I'd say it was a bit of over-kill. They could've supplied the cable though.

My mom has a 1-story 3-BR house with a cheapo Spectrum combination modem/WiFi router to service the whole lot and patio out back. The problem is that the WiFi signal doesn't even make it to the front bedroom, much less out to the patio or into the front yard. I thought the Winegard Extreme would allow us to extend her services at least into the yard so we could stream to a smart speaker, phone or tablet when we were outdoors; but to my surprise, it actually improved wireless performance throughout the interior of the house as well! Out of the box, the antenna is about the size of a soccer ball and weighs roughly one pound--I was expecting something much heavier for its size, but it's almost feather-light so you don't have to worry about it ripping off your siding or bending a flagpole when it's mounted. The box includes both wall and pole mount hardware and a weatherproof mount that covers the port for the Ethernet cable...you'll need to provide at least one cable of your own just to power it up, and maybe a second if you want to use it in access point or bridge mode. Setup is exceedingly simple; if you have a router in your home already and have even glanced at the admin panel to set passwords or activate guest networks, you're already qualified enough to configure this antenna for use. The kit comes with a PoE (Power over Ethernet) injector that sadly is not weatherproof...if you plan to mount the antenna outside (likely, though not required!), you'll have to run an Ethernet cable from the injector through a wall or window. But once it's powered up, a simple web interface allows you to set up the antenna from a phone, tablet, or PC in Extender mode. With this mode of operation, the antenna picks up the 2.4Ghz signal from your home router/network and rebroadcasts its own network SSID using the captured bandwidth from your network and its own antenna hardware. Sadly, this also means the quality and speed of the rebroadcast extension signal is totally contingent on the speed and quality your network's 2.4Ghz signal at the mounting point. In the case of my mom's network, she gets ~65Mbps in the same room as the router, about 20Mbps at the front of the house, 2.0Mbps in the front bathroom, and no signal outside. This meant I was going to need to use an Ethernet connection from the main router to get any kind of usable WiFi signal at or beyond the front of the house. Running another Ethernet cable from the router to the PoE injector, you can now change the antenna to operate in Access Point (AP) mode (essentially turning the antenna into another WiFi router) or Bridge Mode (pass-through of existing router connections so that anything connecting to the Winegard Extreme’s SSIDs/network will get the same IP subnet as all other devices connected directly to the main router--useful for things like home media servers, LAN parties, shared printers, etc.). I ran the Winegard in AP mode and WiFi performance jumped through the roof--not only in the front and back yards, but also inside the house itself. In the outdoor locations that formerly had no service, as well as the spotty front bathroom that barely tipped the scales at 2Mbps, we were suddenly streaming at 25-30 Mbps (that was even through two exterior walls at the front and back of the house and 4 interior walls between them). Better still, at virtually every indoor bedroom, the outdoor-mounted Winegard was delivering a consistent 60-65Mbps INSIDE the house! I didn't even need to turn on the 5Ghz antenna because the 2.4Ghz speeds were maxing out at the cap for my mom's Internet service--but if you have faster service from your ISP, the ability to sprinkle in a little 5Ghz special sauce will be a welcome addition to your newly "robustified" network. Just a few quirks of note. First, there aren't any displays, LEDs, or other status indicators to suggest what the Winegard is up to...which is unfortunate, but understandable given that once you set it up for outdoor operation, it should be able to run unattended and not offer any would-be network saboteurs a tantalizing target for wreaking havoc on your home network. Second, if, for some reason, you accidentally (or purposefully) set the antenna to Bridge mode and then change your mind about it, a factory reset is necessary, but it's a bit obtuse and inconvenient to activate. You have to power on the unit (it probably is on already, right?), wait 90 seconds, and then power off. Rinse and repeat 3 times--then on the next power up, the system will start the reset process which takes about 5 minutes. Again, there are no displays or controls on the unit itself to let you know just where in this process you might be, so this operation takes a bit of patience and faith. Finally, the Ethernet port on the back of the main unit is mounted upside down and jammed right up against the top of the cutout in the antenna assembly. If you need to remove the Ethernet cable from the port for any reason, there is basically not enough room to get a finger onto/over the little plastic snap/retaining arm of the Ethernet jack to release the cable from the port--a cable with a snagless end or integrated boot that grabs the retaining arm for you makes all the difference here. Still, these are all pretty minor niggles for the performance boost and flexibility you get with this unit--definitely recommended if you've got a smallish outdoor footprint you want to extend services to, or if you just want to set the antenna up on a shelf inside the house to improve coverage of your existing indoor network.

Fast internet once you’ve set up the Winegard Extender. Physical setup was done in a jiffy, and there aren’t that many pieces to put together. I ideally wanted on my fence by a main street but you are bound to an area with a power source. If only this was rechargeable. You’ll also want to make sure that the power source protects your power box from the elements. Technical setup took longer than expected and was not as simple as plug and play. I had to manually reset the device three times before it was remotely close to being ready. It took a good 2-3 hours of headaches to get it going. Once it was setup I took my pup on a walk and it’s awesome how much distance we get with our wifi! I truly get a lot of distance for my wifi and can’t wait to move this to our beach home where we go for walks and sit on the dock to fish. We always talk about how the wifi drops and now we’ll have a permanent solution to getting the internet to reach out on to the bay while we cook or fish! This is perfect for a home with a lot of square footage and equally ideal for: ranches, beach homes, large properties, lake houses, condos, and more! With a family like mine that has 50+ wifi devices between individuals and smart home items I think this will solve spreading out our wifi range immensely! Totally scored with the Winegard Extender!

Easy to setup to a 2.4 network. Even easy to setup broadcasting for 5.0 but i couldnt get it to connect to the 5.0 network so you connect as 5.0 but from the extender to the router i could only get 2.4 plus when i received the extender it didnt come with the L pipe to mount it. Best Buy didn't have any replacements in stock so i got a partial refund. Works great though.

Its just ok. The range is fair, but not impressive. I live on alot of land. This helped get better signal to our outdoor devices however i still ended up running another router to the guest house because the signal was too weak to stream with this extender. I considered returning but its good enough for outdoor cameras.

Works as advertised. Installed the access point outside to provide internet access to my outdoor living space.

I didn’t believe the product would work as expected, but was pleasantly surprised. We were trying to get Wi-Fi at a barn about 350 feet away from the house. Worked like a champ. Have already suggested to friends and family.

Awesome product, highly recommend! An easy way to boost your internet coverage to a secondary building from home base.

Easy set up - after simple installation - set up took less than 10 minutes.

I was a bit hesitant to try out this product. I recently sold my home in a major city, and moved into a more rural area. I ended up with a workshop, which is located about 450 feet away from the home. I attempted to use a mesh network to solve my WiFi troubles while working there, but found the speeds dropped significantly from my inside speeds of 400 to about 2 Mbps if I was lucky. In researching outdoor WiFi solutions, the previous generation Winegard was one of the first products recommended. So, I was excited to get an opportunity to try out the newer generation device, hoping to gain some much needed speeds for my YouTube DIY videos. In the box, was the extender, which is around the size of a small 8 inch subwoofer, a mount similar to those found with a satellite dish for attaching to your home or a post/pole, an ethernet cord, and a power over ethernet power (PoE) adapter. I was surprised with just how lightweight the device was, believing it would take more effort to mount the device. I should note, the power adapter doesn't appear to be weather resistant, so you will need to keep this in mind during the installation. There are essentially two ways you can set the device up. You can either use this as a simple extender, in a similar way as other WiFi extenders, or plug an ethernet cable from a nearby router into the PoE adapter to act as an access point. The benefit of using ethernet, is that it seems to share the same IP address range as your main network; thus allowing you to access your other internal network devices, such as a home server. In my case, I simply wanted to gain some better coverage while working outdoors and in my small workshop. Setup of the device can be done using a laptop, tablet, or even your phone with a web browser. If you’re curious, there is a sticker with a default network name and password that you’ll use to login to the admin settings of the device once it’s powered. This allowed me to then scan for available networks, enter my home routers network password. The admin page will also give you some basic signal strength, and given it was attached to my home near one of my mesh network nodes, the signal strength would bounce between 80-88% at any given moment. It did take about 2 to 3 minutes for the connection to fully establish, but once complete I was able to see the new network pop up on my iPhone. My ISP provided speeds range between 380 - 450 Mbps when connected to my home network in the house, and I was able to easily achieve around 120 Mbps on average when connecting about 400-500 feet away. Once I entered the workshop, that speed dropped to around 80 Mbps, which was still a significant boost over the previous 1-2 Mbps speeds seen without the extender. Overall, I was really impressed with the easy setup, the boosted speeds around my yard, and now only get the occasional buffering when trying to watch media content in the shop. In my open yard, I was seeing speeds I’d never seen from a wireless node near a window, and was happy to see my friends enjoying connectivity in our back patio. While this device does state it will go about 1000 feet, I found that speeds began degrading about 800 - 900 feet during my use; with speeds hovering around 2-5 Mbps at roughly 1000 feet. However, this definitely solved a need for me, and I’m happy with the results!

It works great so far. Covers a wide area and improves over all coverage. Light weight and easy to mount outside.

Looking to extend your Wi-Fi range outdoors? Well the Winegard - Extreme 2.0 High Performance Outdoor Wi-Fi Extender is exactly what you are looking for! Upon opening the box you will be greeted with parts to assemble. This is where I deducted the system because it lacks hardware to attach to say a post or side of home. The lack of bolts to do this was disappointing. Second they don’t included a cat 5 cable that is required. The rest of the included hardware is sufficient. Once you get the hardware situated, you then can connect to your Wi-Fi and boom all set. That part took all of 2 minutes versus the install took 20-25 after drilling etc. Over all how is the speeds? Well I was able to extend my Wi-Fi to edge of the street to the house so it cover the security system solid now. Strength was mid- to mid high. I saw consistent speeds on my internet ranging from 55-300. Overall this product works as intended and has a pitfall with its mounting hardware or lack of a few pieces. Solid pick and it’s weather proof!

Out of the box the unit is significantly lighter than I would have ever expected. The unit comes with mounting hardware and plug in outlet. Setup was not simple, or I am, either way I did have to go to the manufacture's website. On the website they have handy help YouTube video on everything from initial setup, mounting, to additional features. Speed testing on the inside and outside of the house left me with these conclusions. One, if you are close enough to your actual router to be connected to that router, do it. Two, the Winegard - Extreme 2.0 will not amplify the boost for the original signal. It is like it only widens its diminishing range. Meaning, if my actual routers speed test had a 375 mbps down and 75 up when on its Wi-Fi and close enough to be within the routers line of sight. The extender would have almost or lower that same value at that same location. However, once you started walking away the actual Wi-Fi would diminish rapidly whereas the extender would diminish but slower therefor allowing you to extend your signal. It did not ever boost the signal so the mbps was always on the low side with the extender after about thirty feet. When the actual normal router gives out, the extender was on average only at 8 - 16 mbps with a continual diminish to barely connecting after 250'+. Disclaimer, when testing we had not mounted the extender yet. I would recommend mounting high enough to allow for a larger line of sight and switching on the 5.0 GHz if you have it. Afterwards results did improve but without measuring I would be hard pressed to believe it could 1,000’. When mounting I had to run the ethernet cable down to an existing cable hole and had to drill out the silicone. I am excited for what my cable company has to say about that. So, I could feed the cable through the attic. I unfortunately figured out that the only power supply outlet in the attic was on the other wall from the drop. Get a spool of cable to make sure you have enough length at your disposal. Past that, I am very satisfied with this unit. We had some dead spots on the property and now we do not. I have even mounted some battery-operated security cameras in areas of my property that I could not have otherwise monitored before without professional help.

The Winegard Extreme 2.0 Outdoor Wireless Range Extender/Access Point is a quality outdoor capable piece of network hardware. The design of the access point and mounting hardware seem strong enough to stand up to the elements and the range of the signal is awesome. Unboxing the Winegard unit was a bit of a surprise. The packing was very simple and industrial and the quick setup instructions were just a single front and back piece of paper. I am a capable IT engineer but I feel comfortable saying almost anyone would be able to set up the system with the included guide - it just isn't as pretty as some more polished presentations from major brands. Out of the box, the unit comes set for "range extender" mode where it connects to another wireless network and then broadcasts a new network with a new subnet and NAT. This was a little confusing to me and could cause some issues with home setups that rely on devices being in the same broadcast space - for example, if you have a TV on your deck with chromecast capability, you wouldn't be able to connect your phone to the Winegard unless the TV was also on the winegard, even if it was within range of your "indoor" network. Where this might be useful is if you were using the Winegard for a guest house or airbnb space on your property - you could easily share an extra network with your guests that is at the edge of your normal wireless range. It was a fairly simple process to change the settings and put the device in Bridge mode as a standard wireless access point - although I do think it required power cycling the device even though it wasn't specified until I got to that point. Once I got the Winegard set to bridged access point mode, I was really happy with the speed and coverage. I walked down the sidewalk to the far edge of my neighbor's property, and the Winegard was providing a better signal than my neighbor's own wifi router. Very impressed. Only real knocks on the product are the limited quick setup instructions and the wireless settings limitations I described above. In the right home network, this thing provides a major boost for your outdoor living space.

Will reach close to spec range, albeit at fairly reduced speeds (which is expected) Good enough for basic networking at range, but anything within 100ft outdoors is able to max out my 100mbps internet connection. Larger unit than expected, I work in networking, and it rivals the size of the bigger outdoor APs I've seen, while feeling much cheaper/hollow. My biggest gripe is non standard POE. I asked the manufacturer if it was 802.3af/at, and it's not, they only want you to use the included injector. (Sticker on the bottom of unit shows 24v) Not a big deal for most that won't even have a POE switch.