Questions & Answers

Q: QuestionWhat is the wattage per channel for this receiver?

• A:Answer This receiver offers 100 watts per channel at 8 ohms.

Q: QuestionWhat is the maximum resolution supported by this AV receiver?

• A:Answer This receiver supports a maximum resolution of 8K.

Q: QuestionDoes this receiver support Dolby Atmos?

• A:Answer Yes, the receiver supports Dolby Atmos for immersive surround sound.

Q: QuestionDoes this AV receiver have a phono input?

• A:Answer Yes, this receiver has a phono input for connecting a turntable.

Q: QuestionThe wattage per channel is not listed. What is the per channel and total wattage?

Asked 5 years ago by MusicMatters210.

• A:Answer 100 watts per channel at 8 ohms

  Answered 5 years ago by Bryan

  Helpful (20)Unhelpful (0)ReportAnswer this question

Q: QuestionHow does the RX-A2A differ from the less expensive RX-V6A? The only differences I can spot are the different remote, the fifth leg on the A2A, and a longer warranty on the A2A. Thanks!

Asked 5 years ago by Austin.

• A:Answer The advantage, has better made components on the inside, power capacitors, etc and the extra foot! Or support would make a difference

  Answered 5 years ago by Hotsauce1725

  Helpful (17)Unhelpful (1)ReportAnswer this questionShow more answers (1)

Q: Question“I understand this unit will allow me to bi-amp my main speakers. Can I also use zone 2 for patio speakers?

Asked 4 years ago by cm.

• A:Answer I said "yes" earlier but found out, by trying it myself (and spending on an extra set of speaker cables), that you cannot bi-amp the main speaker AND use zone 2. Although the receiver has enough connections to wire both, in the "Power Amp Assign" menu you can only select one or the other. If you select "Bi-Amp" here, the zone 2 speakers are silent. If you bi-amp the speakers and use the "7.1 + 1 Zone" or the "5.1.2 + 1 Zone" setting, you get your zone 2 speakers but your main speakers get different signals for the tweeter and the woofer when you play 7.1 or 5.1.2 audio which is not what you want. For passive bi-amping, both terminals on the speaker should get the same audio signal delivered through two wires. So the short answer is, no, this feature is NOT supported. Unfortunately, the manual does not tell you this explicitly.

  Answered 4 years ago by Austin

  Helpful (8)Unhelpful (0)ReportAnswer this questionShow more answers (5)

Q: QuestionDoes this receiver have the same HDMI 2.1 Issue that both the RX-V6A and RX-V4A have with the Xbox Series X and PS5? From my understanding it’s the chipset that isn’t compatible.

Asked 4 years ago by FROD.

• A:Answer My understanding is it does. The good news perhaps, (Yamaha) has yet to respond, but Sound United who owns Denon and Marantz responded on 12/9 that "Sound United completed additional testing and is pleased to report that 4K/120Hz passthrough works without issue on Nvidia and PS5 devices. Outside of what was originally reported regarding Xbox at 4K/120Hz output setting, we have had no further HDMI 2.1 device interoperability issues reported as of this writing. " This is good news as the chipset is the same as Yamaha, so it may not be a hardware issue with the chipset that was first reported across the three brands. There is not further details on the Yamaha site for a firmware update, but hopefully that means they will follow the same fate. In the same response Sound United indicated they have made good progress on the Xbox issue as well. I know this is an exact answer for Yamaha, but good news given the updates from Sound United. If you want to read more, this is the details of those: https://www.audioholics.com/news/sound-united-hdmi-2.1-no-issue

  Answered 4 years ago by TheDPG

  Helpful (6)Unhelpful (0)ReportAnswer this questionShow more answers (3)

Q: QuestionThe 7.2 receiver ...can It handle 14 speakers or do I need a 9.2?..

Asked 4 years ago by Sportsdoc.

• A:Answer A total of 9 speakers can be connected to this receiver, but only 7 will be powered at a time.

  Answered 4 years ago by MountainLoverVerified Purchase

  Helpful (5)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionThe JBL speakers I want to pair with theses are 4 ohm. Can this receiver run at 4 ohms without damaging my speakers or is it incompatible?

Asked 4 years ago by TVbuyer.

• A:Answer Ohm settings on the receiver are adjustable to match your speakers.

  Answered 4 years ago by SteveVerified Purchase

  Helpful (5)Unhelpful (0)ReportAnswer this questionShow more answers (2)

Q: QuestionI am interested in the Yamaha AVENTAGE RX-A2A model to bring it to chile. Here the electrical power is 220 watts. can this model work with 220 watts?

Asked 4 years ago by DonCarlos.

• A:Answer Unless Yamaha sells a model rated for 220 volts the current US model is 120 volts only. Purchase a small 120 volt to 220 volt transformer. Just make sure transformers output has sufficient wattage to power receiver and any other components that need power.

  Answered 4 years ago by PreciseElectricVerified Purchase

  Helpful (3)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionIs the unit able to run only 5.1?

Asked 4 years ago by Don.

• A:Answer It can. I set them up in 5.1 quite often

  Answered 4 years ago by AVGuyVerified Purchase

  Helpful (4)Unhelpful (0)ReportAnswer this questionShow more answers (3)

Q: QuestionFM tuner ? Re: Yamaha RX-A2A

Asked 5 years ago by Keith.

• A:Answer There is one but why use it. The internet radio is much better. Most over the air radio stations are streaming as well

  Answered 4 years ago by AVGuyVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (2)

Q: QuestionIs the November 27th Pickup day accurate? I tried looking for a release date on this model and haven't found a confirmed date.

Asked 5 years ago by hamachiko.

• A:Answer Update on my earlier answer: I got my unit today, two days after the scheduled date. The delay affected other unrelated items as well (like the new game consoles) that were scheduled to be available on Black Friday, so it appears it was simply a delivery issue.

  Answered 4 years ago by Austin

  Helpful (2)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionHow many bands of EQ does this receiver have?

Asked 2 years ago by JoBa.

• A:Answer 7 band EQ. ±6.0 decibels at 63 Hz, 160 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.3 kHz, and 16 kHz.

  Answered 2 years ago by bxzxVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionCan I hook up a sub a set of fronts a center a set of surround backs and a set of Dolby atmos speakers?

Asked 2 years ago by JoeyT.

• A:Answer Yes, I had a Best Buy technician set this up in my home exactly as you described. Sounds amazing!

  Answered 2 years ago by AnonymousVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionMY YAMAHA AVENTAGE RXA2A RECEIVER , VOLUME GOES UP AND DOWN WITHOUT TOUCHING THE VOLUME CONTROL

Asked 3 years ago by Anonymous.

• A:Answer This is not a question

  Answered 2 years ago by DennisBVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionLooking to purchase a new receiver my pioneer elite SC-LX502 is giving me issues and is still under warranty. Looking at this Yamaha RX-A2A & Denon X2700H. Being they are basically in the same price point which receiver would be better for my 7.2 set up

Asked 3 years ago by Paul.

• A:Answer I would go Yamaha all day the RX-A2A excellent build quality does not get hot like Denon, Yamaha purer/cleaner sound.

  Answered 3 years ago by TechieVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this question

Q: QuestionI have a 7.2 inside and 2 speakers outside. Will this 7 2 receiver allow you to connect the 7.2 setup that's inside and 2 speakers outside as zone 2 without any additional equipment.

Asked 3 years ago by Coreypso.

• A:Answer Yes, should work

  Answered 3 years ago by SonyOLEDVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)